Expansion
1297
Votronic USB loader panel S
Switch and safety panels for the on-board electrical system
Switch the electrical devices and secure circuits, put together individually according to their own wishes and mark them clean. These are the characteristics of these control and switching devices. Equipped with fuse machines, the annoying search for the right replacement protection has come to an end. The operational readiness is restored at the push of a button. Panels with a uniform height of 85 mm are offered for the Votronic module system that can be used as individual devices or in combination. The diverse application options allow the user to put together a complete information and operating center.
Security panel 4 s
Safety machines 6a, 8a, 10a, pre -wired to the group
1 safety machine 12a, individually damable
Suitable for 12V and 24V
Connection via flat connector
Optical trigger control
Other base on request
Front disk aperture S
Blind cover for already planned panels or to install your own components
Switch panel 4 s
4 switch on/off, 8a each resilient, with a control LED
Connection via screw terminals
Execution 12V or 24V
Switch panel 2x 16a s
2 single switch 2xum with flat plug connection
Resilience: 2x 8a / 1x 16a
Suitable for 12V or 24V
Main switch panel 20a S
Robust main switch with 20A overcurrent switch (automatic safety machine)
Thermally triggering, briefly overloadable for a short time
Triggering with more than 20a permanent current with the reversal of the switching rocker
Suitable for 12V and 24V
USB loader panel s
USB double-carer5V / 2.5A
Suitable for 12V and 24V
Switch panel 16a s
Individual switch 2xum with flat plug connection
Resilience: max. 2x 8a or 1x 16a
Suitable for 12V or 24V
STCKOSE PANEL S
For 12V consumers with DIN connector (ISO 4165), resilience 8a
Connection via flat connector
Device type
Art.-No.
Art.-No.marine
Operating voltage[V]
Dimensions(B x H X T)[mm]
Installation depth approx.[mm]
execution
Security panel 4 s
1285
-
12 and 24
47 x 85 x 75
70
A
Switch panel 4 s
1287
11287
12
47 x 85 x 25
20
B
Switch panel 4 / 24v s
6287
16287
24
47 x 85 x 25
20
B
Switch panel 16a s
1289
-
12 and 24
47 x 85 x 45
40
C
Switch panel 2x16a s
1291
-
12 and 24
47 x 85 x 45
40
D
STCKOSE PANEL S
1293
-
12 and 24
47 x 85 x 65
60
E
Main switch panel 20a S
1295
-
12 and 24
47 x 85 x 75
70
F
USB loader panel s
1297
-
12 and 24
47 x 85 x 42
38
G
Front disk aperture S
2019
-
-
47 x 85 x 3
-
H
Scope of delivery:
Flat plug, fastening screws, drilling template
An internationally understandable lettering sheet is available for the clean labeling of switches and fuses. This Pictogram film is transparent, self -adhesive and suitable for the vottronic front platform design.
1234567891011121314151617181920
Fresh water tankSewage tankFecal tankFuel tankTank insideTank outsideTank 1Tank 2Tank in generalTank heatingOn-board batteryStart batterySolar batteryBattery 1Battery 2lightingLighting kitchenLighting medical spaceLighting outer doorLighting storage space
2122232425262728293031323334353637383940
RefrigeratorHeatingboilerpumpfanfanradioTVVideo recorderSatellite receiverStove/microwaveElectrical levelElectrical awning12V socket24V socketAlarm in generalCarbon monoxide alarmGas alarmIce-exHeadlight
4142434445464748495051525354555657585960
Power supply unitVoltage converterAttention network voltageNetwork 230V12V equal voltage24V equal voltageAAOut ofOut ofOnOffphonefaxreserveLoadDistribution 1Distribution 2Addition (general)Main (general)
61626364656667686970
Fuse 4aFuse 5aSecurity 6aFuse 7aFuse 8aFuse 8aSecurity 10aSecurity 10aFuse 12aFuse 16a
TEX1760
Parking heater kit VW T5/T6 with Autoterm Air 2D (Planar 2D) PU-27 OLED Display
Retrofit auxiliary heating at VW T5 / T6
With this underfloor installation kit for an Autoterm Air 2D (Planar 2D) Saxor heating, the original plant is used for this purpose - passenger side underground between the step and B pillar.
Is included:
The heating itself,
The installation lan for the underfloor assembly at the corresponding position in VW T5 / T6,
All parts required to realize the air intake in the stepping level
Adapter to use the original warm air channels from Volkswagen for the B-pillar on the warm air side.
In total, you get an almost original installation in the cleanest possible way.
The air-leading parts for the B-pillar are not included and must be ordered from the Volkswagen dealer. The costs for this should be less than EUR 150 (no guarantee on this information, since we cannot always keep an eye on the VW prices!). You can automatically receive a list of the required partial numbers by email after purchase.
Autermeitungen offeurers
The diesel parking heaters from Autoterm, which have become known under the name Planar 2D, are now called Air 2D.
They are the robust, proven heating for the camper self -building - installing yourself without loss of warranty and provided with e -test marks, which means you are safe in operation and do not need to be entered by the TÜV.
The simple technology can even be repaired in an emergency.
maintenance
With an autoterm heating there is only one maintenance measure and it is also super simple: don't just let it run on the smallest level! If you operate the heating mainly in the low area, let it run every 1 - 2 weeks for half an hour to burn away from starting soot deposits. Complete!
Operation at large heights
The operation of diesel devices and engines is a problem at high heights. But not for the diesel heaters in our installation kits. They are equipped with a height kit that automatically adjusts the fuel injection to the changed air pressure conditions.
The altitude kit was tested under real conditions (on the Pitztaler glacier). However, our customers have now broken our height record and operated the heating at a height of over 5000 meters without any problems.
The following also applies here: when returning to a normal level over zero, the heating must get the opportunity to burn free!
What controls are there?
When ordering, you can choose between different control panels.
PU-5: A simple control panel that is controlled via a rotary control, by means of which you select a performance level. A separate temperature sensor (article number 16522) must be ordered to adjust a temperature control.
PU-27: This control panel has already integrated the temperature sensor. If the cable length of 1.80 m is not sufficient or if you want to assemble the panel at a location unsuitable for the temperature measurement, the separate temperature sensor can alternatively be used.
Comfort Control: The new, improved control panel for the Autoterm / Planar Sace heating. With three freely adjustable timers for any weekday, expanded heating modes (including thermostat mode), voltage monitoring and much more. Multifunctional bike with pleasantly handy rubber coating and OLED display. Smaller installation road, more comfortable use, more chic design.
remote control
A separate remote control can be used to control the heating. The wiring harness has an extra switching input that can be used for this.
The control can be carried out permanently by connecting the two cables of the switching input by switch or relay, then the heating runs until the connection is separated again). But you can also use an impulse of 0.5 to 3 s length. In this way, several control parts can be used - for example, switch on and regulate from the seat, later in bed via remote control without having to get up.
Technical specifications:
Operating voltage: 12 VHeating power: 0.8 kW (min), 1.8 kW (max)Air volume flow: 34 m³/h (min), 75 m³/h (max)Fuel consumption: 0.1 l/h (min), 0.24 l/h (max)Performance recording: 10 W (min), 29 W (max)
Scope of delivery:
Heater 12 V
Digital control panel (please select the desired variant)
Low-no-no autoterm fuel pump "Extra quiet"
Exhaust gas absorber (17 x 9 x 5 cm)
Rubber holder dosing pump
Dosier pump wiring harness
Wiring harness
Suction air hose with integrated silencer
Heat protection hose
End piece exhaust pipe + clamp
Tank
5.5 m fuel line
Fuel bonds
1 m exhaust gas reed tube metal
Screws, nuts, clamps, shrink hose, cable ties
operation manual
Attention fuel hose:
The scope of delivery includes fuel hose, which can be used as a “adapter” to connect the fuel line. The length is usually sufficient (parts if necessary). If you still need something of it, you can do the hose under the Article number 35612 Request as meters.
A T -piece for the fuel line is not included - the fuel removal can be realized if there is an existing cheater, in this case must Article number 17890 be ordered.
Dimensions:
Length: 33 cmHeight: 12 cm + 2.5 cm connectionsDepth: 12 cmWeight of the heating without accessories: 2.86 kg
Additional options heating
T-piece fuel line / fuel line 8 x 5.3 x 8mm
T-piece fuel line / fuel line 5.3 x 5.3 x 5.3mm
Autoterm connection cable control element for 7m
Autoterm extension cable control element 3M
External temperature sensor with 5m cable
Suction hose with filter for Autoterm Air 2D, 4D and Flow 5D
Variants from €669.90*
N20804S
Marinco Solar fan Day and Night 100mm = 4 "stainless steel
New design!
One/off switch for the fan, LED lighting and intake/exhaust switch switch is accessible for easy operation from the cabin!
Allows fresh air circulate in the boat cabin and thus prevents mold and musty smell.
Moves 1,000 cubic foot air/hour or 24,000 cubic foot air/day (4 "model)
Recharged battery enables 24 hours of continuous operation
Whispering fan operation
No cabling required
Built-in on/off switch for the fan, LED lights and switches for intake/exhaust air
Nimh battery with a high capacity runs the fan with a full load of up to 24 hours without sunlight
Is screwed into the supplied cover plate and can be removed from the outside without tools
All Day/Night Plus models are delivered entirely with white plastic inner ring, insect protection grille, assembly material and an easily understandable installation instructions
Replaced Nicro 3 "and 4" (fits in existing holes) and Day/Night Plus models
TEX1921
Autoterm Air 2D (Planar) 12V Comfort Control 83mm
Installation kit with Autoterm Air 2D heater - Fits in 99% of camper cases
This set meets all the requirements of 99% of all campers. Also for larger touring vehicles up to approx. 16 cubic meters of heatable volume (volume without furniture!).
The idea is that the heating is used for continuous operation. This means that the heating is not switched off but continues to run at a low power level. Keeping a room at the right temperature uses significantly less energy than trying to heat up a cold interior in 30 minutes.
We assume that all vehicles are properly insulated and that in winter the driver's cab with its large, uninsulated windows is at least separated by a blanket.
Don't worry: The heater is designed for continuous operation and has no problem with it. In principle, you can drive off at home, turn on the heating and turn it off again in 4 weeks when you get home. The power consumption at the lowest level is 10 watts, which is less than the parking lights of your van.
Height kit / heating maintenance
The heater is equipped with an altitude kit, which means that it also works in the Nepalese mountains or in the Andes. But that doesn't mean it can't sooty! If you leave the high altitudes, run your heating at full power for an hour so that deposits can burn away.
The burn-off is also necessary if you only operate the heater at the lowest level for a long time. Set it to full power every 1 - 2 weeks at the latest so that the combustion chamber gets really hot again. This is the most important and at the same time the only maintenance measure on the heating.
The 99% kit consists of the following parts:
Our bestselling diesel parking heater: Autoterm Air 2D with 2 kW heat output and altitude kit for vehicles with 12V.
Technical data Autoterm Air 2D (formerly Planar 2D):
Operating voltage: 12V
Heat output: 0.8 kW (min), 2 kW (max)
Air flow rate: 34m³/h (min), 75m³/h (max)
Fuel consumption: 0.1ll/h (min), 0.24l/h (max)
Power consumption: 10W (min), 29W (max)
Hot air piping 60mm system
The complete installation kit for the heater is also included:
12V heater
low-noise Autoterm fuel pump, "Extra Quiet"
Exhaust silencer made of stainless steel (17 x 9 x 5cm)
Rubber holder dosing pump
Dosing pump wiring harness
Heater wiring harness
Intake air hose with integrated silencer
Heat protection hose
Exhaust pipe end piece + clamp
Tank suction pipe
5.5 m fuel line
Fuel line connector
1 m metal corrugated exhaust pipe
Screws, nuts, clamps, shrink tubing, cable ties
Instruction manual
Also included:
Control panel depending on the selection:
PU-5: A simple control panel with rotary control. It controls the heating via power levels. A separately ordered temperature sensor can be connected, then the room temperature can be controlled with the PU-5.
PU-27: The digital control panel with OLED display has an integrated temperature sensor (cable length 1.8 m), but an external temperature sensor can also be used be connected if the control panel is installed in an unsuitable place (e.g. in a cabinet). Control via a fixed power level is also possible. The device has a timer function. Menu navigation in English and Russian.
Comfort Control: The new, improved control panel for the Autoterm / Planar parking heater. With three freely adjustable timers for any day of the week, extended heating modes (incl. thermostat mode), voltage monitoring and much more. Multifunction rotary wheel with a pleasantly non-slip rubber coating and OLED display. Smaller installation dimensions, more comfortable use, more stylish design.
Cable length heating control panel, approx. 1.80m
The cable length to the control panel in the manufacturer's scope of delivery is 1.80m. Various longer replacement cables or extension cables are optionally available.
mounting flange
Our built-in stainless steel flange that makes installing the heater simple, elegant and sexy.
It is sufficient to cut a rectangular hole (9 cm x 13 cm) in the vehicle floor to mount the heater flat and thermally decoupled. Then the tigerexped installation flange can be glued or screwed (please use a PUR sealing compound instead of silicone).
You can choose the size of the flange: For floors up to 48 mm (enough for most vans) or for 83 mm floor thickness (usually for cabins or high insulation and floor panels). The flange should be at least 5 mm longer than the floor is thick (for the sealing joint).
T-pieces for the fuel supply
2 different T-pieces (8 x 8 x 5.3 mm and 5.3 x 5.3 x 5.3 mm) to use your vehicle's original fuel system for the fuel supply, IF it is ensured that this works for the vehicle and heater (pressure, length of the return line, etc.) or if there is already an auxiliary heater whose tank extraction can be used.
If this is not possible or not safe, there is also a tank extraction pipe in the kit so that you can take the fuel directly from the fuel tank (usually the method of choice).
Attention fuel hose:
The scope of delivery includes a fuel hose as a line connector. The included length is usually completely sufficient (possibly shorten/divide pieces). If, contrary to expectations, you can't get by with it, you can reorder the hose by the meter.
Fuel filter
A fuel filter so that the heater always gets clean fuel. In the case of diesel from non-European countries or vehicles with rusty tanks, this is life insurance for the fuel pump of the heating system. Attention: Do not mount the filter horizontally, but at a slight angle so that the pump always sucks from the filled side of the filter!
Hot air pipe
The set also includes 3 meters of 60 mm warm air pipe. In 99% of the cases this is a well-measured need.
Warm air outlets / distribution
A suitable Y-piece and 2 vents 60 mm, rotatable, so that you can decide for yourself where you want to mount the two air outlets.
The right kit?!
The heating kit is suitable for vehicles with an interior of 12 cubic meters to 14 or a maximum of 16 cubic meters - depending on the insulation and furnishings, placement of the hot air outlet openings, personal temperature feeling and the climate in which you drive But e.g. for all VW transporters and up to H2L2, this heating should be sufficient for common travel destinations.
If you have a larger vehicle, don't want to isolate yourself or want to / have to do the balancing act between the Sahara and wintry Siberia, you've come to the wrong place!
In the VW T5 / T6, the installation site for an air heater is prepared at the factory, the 99% camper kit would be unsuitable here, we have another suitable T5/T6 installation kit.
.
Variants from €684.90*
SHP301602000
Victron stainless steel built-in socket boat camper yacht shore connection 16A
The Victron shore power socket SHP301602000R 16A was specially developed for the boat and mobile home sector. This model features a high quality stainless steel bezel and is compatible with all Victron shore power cables.
Technical characteristics:
Degree of protection: IP 57
Facing Material: Stainless steel
Weight: 0.34kg
max voltage: 250V AC
max current: 16A
Standard: IEC 60309, 2p+E
Type coverage: PA6
Scope of delivery:
1x Victron SHP301602000R shore power socket 16A 250V stainless steel
Delivery time: 1-3 working days
1293
Votronic socket panel S
Delivery time: 1-3 working days!
Switch and safety panels for the on-board electrical system
Switch the electrical devices and secure circuits, put together individually according to their own wishes and mark them clean. These are the characteristics of these control and switching devices. Equipped with fuse machines, the annoying search for the right replacement protection has come to an end. The operational readiness is restored at the push of a button. Panels with a uniform height of 85 mm are offered for the Votronic module system that can be used as individual devices or in combination. The diverse application options allow the user to put together a complete information and operating center.
Security panel 4 s
Safety machines 6a, 8a, 10a, pre -wired to the group
1 safety machine 12a, individually damable
Suitable for 12V and 24V
Connection via flat connector
Optical trigger control
Other base on request
Front disk aperture S
Blind cover for already planned panels or to install your own components
Switch panel 4 S 12/24
4 switch on/off, 8a each resilient, with a control LED
Connection via feather clamping terminals
Suitable for 12V and 24V
Switch panel 2x 16a s
2 single switch 2xum with flat plug connection
Resilience: 2x 8a / 1x 16a
Suitable for 12V or 24V
Main switch panel 20a S
Robust main switch with 20A overcurrent switch (automatic safety machine)
Thermally triggering, briefly overloadable for a short time
Triggering with more than 20a permanent current with the reversal of the switching rocker
Suitable for 12V and 24V
USB loader panel s
USB double-carer
5V / 2.5A
Suitable for 12V and 24V
Switch panel 16a s
Individual switch 2xum with flat plug connection
Resilience: max. 2x 8a or 1x 16a
Suitable for 12V or 24V
STCKOSE PANEL S
For 12V consumers with DIN connector (ISO 4165), resilience 8a
Connection via flat connector
Device type
Art.-
No.
Art.-
No.
marine
Operating voltage
[V]
Dimensions
(B x H X T)
[mm]
Installation depth approx.
[mm]
execution
Security panel 4 s
1285
-
12 and 24
47 x 85 x 75
70
A
Switch panel 4 S 12/24
1288
11288
12 and 24
47 x 85 x 32
25
B
Switch panel 16a s
1289
-
12 and 24
47 x 85 x 45
40
C
Switch panel 2x16a s
1291
-
12 and 24
47 x 85 x 45
40
D
STCKOSE PANEL S
1293
-
12 and 24
47 x 85 x 65
60
E
Main switch panel 20a S
1295
-
12 and 24
47 x 85 x 75
70
F
USB loader panel s
1297
-
12 and 24
47 x 85 x 42
38
G
Front disk aperture S
2019
-
-
47 x 85 x 3
-
H
Scope of delivery:
Flat plug, fastening screws, drilling template
An internationally understandable lettering sheet is available for the clean labeling of switches and fuses. This Pictogram film is transparent, self -adhesive and suitable for the vottronic front platform design.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Fresh water tank
Sewage tank
Fecal tank
Fuel tank
Tank inside
Tank outside
Tank 1
Tank 2
Tank in general
Tank heating
On-board battery
Start battery
Solar battery
Battery 1
Battery 2
lighting
Lighting kitchen
Lighting medical space
Lighting outer door
Lighting storage space
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Refrigerator
Heating
boiler
pump
fan
fan
radio
TV
Video recorder
Satellite receiver
Stove/microwave
Electrical level
Electrical awning
12V socket
24V socket
Alarm in general
Carbon monoxide alarm
Gas alarm
Ice-ex
Headlight
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Power supply unit
Voltage converter
Attention network voltage
Network 230V
12V equal voltage
24V equal voltage
A
A
Out of
Out of
On
Off
phone
fax
reserve
Load
Distribution 1
Distribution 2
Addition (general)
Main (general)
61
62
63
64
65
66
67
68
69
70
Fuse 4a
Fuse 5a
Security 6a
Fuse 7a
Fuse 8a
Fuse 8a
Security 10a
Security 10a
Fuse 12a
Fuse 16a
SHP303202000
Victron stainless steel built-in socket shore connection boat mobile home yacht 32A
The Victron shore power socket SHP303202000 32A was specially developed for the boat and mobile home sector. This model has a high quality stainless steel cover and is compatible with all Victron shore power cables.
technical characteristics
Degree of protection: IP 57
Facing Material: Stainless Steel
Weight: 0.65
Max current: 32A
Standard: IEC 60309, 2p+E
Type cover: PA6
Scope of delivery:
1x Victron SHP303202000 shore power socket 32A stainless steel
Delivery time: 1-3 working days
data sheet
General
item number
8-67-009225
Manufacturer part number
SHP303202000
product type
high-quality 32A stainless steel junction box for shore power cables in the marine and caravan sector
Manufacturer
VictronEnergy
EAN
8719076026099
SHP307700280
Victron adapter CEE plug 16A 3p to CEE coupling 32A 3p 250V
Victron adapter CEE plug 16A 250V 3-pin to CEE coupling 32A 250V 3-pin
max. Current: 32A
Max. voltage: 250V AC
In the shore connection area you will find additional adapters, shore power cables and built-in sockets made of stainless steel and polyamide.
Scope of delivery:
1x Victron Energy SHP307700260 Adapter CEE plug 16A 250V 3-pin to CEE coupling 32A 250V 3-pin
17890
T-piece fuel line / fuel line 5.3 x 5.3 x 5.3mm
T-piece Sprit line 5.3 x 5.3 x 5.3 mm. To connect binar water heating and air heating planar 2D, 4D and 44D to the existing fuel system. (Recommends, for example, on the T5/T6 if there is a heater).
For Binar water heating and air heating planar 2D, 4D and 44D. In this way, the fuel -based tanker can easily be used in the event of existing heaters. Please do not use the engine in front or return.
N20803S
Marinco Solar fan Day and Night 76mm = 3 "
New design!
One/off switch for the fan, LED lighting and intake/exhaust switch switch is accessible for easy operation from the cabin!
Allows fresh air circulate in the boat cabin and thus prevents mold and musty smell.
Moves 1,000 cubic foot air/hour or 24,000 cubic foot air/day (4 "model)
Recharged battery enables 24 hours of continuous operation
Whispering fan operation
No cabling required
Built-in on/off switch for the fan, LED lights and switches for intake/exhaust air
Nimh battery with a high capacity runs the fan with a full load of up to 24 hours without sunlight
Is screwed into the supplied cover plate and can be removed from the outside without tools
All Day/Night Plus models are delivered entirely with white plastic inner ring, insect protection grille, assembly material and an easily understandable installation instructions
Replaced Nicro 3 "and 4" (fits in existing holes) and Day/Night Plus models
35612
Fuel hose, inside diameter 5 mm as LFM
Hose to connect fuel -carrying components
Suitable as a "adapter" between rigid nylon fuel hose and our T-pieces 5.3 x 5.3 x 5.3 mm, pumps and fuel filters for installing Autoterm Air and Flow heaters.
The flexible rubber fuel hose is available as a meter goods. The maximum length that can be delivered in a row is 15m.
6227498270893
Siemens 5SU1356-6KK10 RCCB 2-pole 10A 0.03A 230V
Technical details
Frequency
50Hz
Connectable conductor cross section stranded
0.75 | 35.0
Number of poles (total)
2
Energy Limit Class
3
Rated breaking capacity according to EN 61009
6.0
Rated breaking capacity according to IEC 60947-2
15.0
Rated switching capacity Icn according to EN 61009-1
6.0
Type of stress
AC
Width in pitch units
2
False trip protection
yes
Number of fused poles
1
Rated residual current
0.03
Suitable for flush-mount installation
yes
degree of protection (IP)
IP20
Rated voltage
230
Rated insulation voltage Ui
264
Rated impulse withstand voltage Uimp
4.0
Rated current
10
surge current resistance
1.0
Release characteristic
B
Switching neutral conductor
yes
With locking device
yes
Overvoltage Category
3
degree of pollution
2
Ambient temperature during operation
-25 | 55
Installation depth
70.0
Connectable conductor cross-section, solid
0.75 | 35.0
Delivery time: 1-3 working days
PVB-30
Fohermo photovoltaic water boiler 30 liters - hot water operators
With the 30l water boiler from Fothermo (MPN PVB-30) you can generate your hot water with sustainable and inexpensive solar power. The connection of the solar modules is done in a few seconds in a few simple steps and offers you a reliable hot water supply.
Product highlights
30 liters of photovoltaic hot water boilers
Warm water for the sink, the shower or the kitchen
No connection to the power grid required
Complete system with MC4 PV connections
No specialist required for the installation
Digital temperature display
1/2 "Water connection on the hot water.
Optional re -heating via the power grid possible (accessories not included in the scope of delivery)
Recommended solar performance
We recommend a solar module output of min. 300WP
Connect modules with at least 100WP power and nominal voltage 18V
Connection of max. 3 x 325WP modules in parallel
Danger:
The idle voltage of the solar modules must not exceed 42.4V. When using several modules, these must be switched in parallel, not in series
Technical specifications
Volume: 30 liters
Max. Heating power: 550W
Max. Electricity: 15.5A
Protection class: IP 24
Dimensions: 400 x 400 x 600 mm
Weight: 15 kg
Scope of delivery:
1x fechermo 30 liters of hot water boiler (PVB-30)
1x fastening set
73540301
Spelsberg AK 03 small distributor, 3 modular widths, 1 row, IP65
Safe - Thanks to the high degree of protection IP65 and the robust, halogen-free design, safe operation is guaranteed even under harsh industrial environmental conditions.
Material:
Box: polystyrene, light gray similar to RAL 7035
Lid: polystyrene, light gray similar to RAL 7035
Hinged window: polycarbonate, transparent
Seal: Polyurethane
Cover screw: Polyamide 6, glass fiber reinforced
More properties:
Color: grey
Protection class: IP65 - according to EN 60529 / DIN VDE 0470-1
Number of pitch units: 3
Heavy metal free
PVC-free
Silicone-free
sealable
Impact strength: IK07 according to DIN EN 5012 / VDE 0470 part 100
Cover screw torque: 1.2 N m
Environmental conditions:
Ambient temp. (minimum): -25°C
Ambient temp. (maximum): 40°C
Ambient temp. (24 hours): 35°C
Max. rel. Humidity at 25°C (short term): 95%
Max. rel. Humidity at 40°C: 50%
Dimensions:
Width: 100mm
Length: 150mm
Height: 96mm
Internal height: 95mm
?Delivery time: immediately from stock
5555
Votronic tank electrode 20 K toilet
The Votronic tank electrode 20 K-WC (HAN 5555) is a tanker for cassette toilets in motorhomes that are now considered an absolute standard. Cassette toilets are compactly constructed and have an advertisement, which unfortunately unfortunately only marks the full state. Once this has been reached, the toilet in the vehicle can no longer be used. The use of tankers in combination with votronic filling displays enable forward -looking planning of the disposal and renewal of your mobile tanks.
The essential product properties of the 20 K-WC tanker
Tanker specially designed for cassette toilets and mobile tanks
Compact, robust, waterproof (IP67)
Easy assembly, no revision opening required
With a 3-pin round plug connection to separate the tank
Complete assembly material included
Stable electrode, easy to shorten at tank height
Installation diameter 38 mm (or PG 29 thread)
Flange diameter 46.5 mm
Test mark: E-test (EMV/car directive)
Connection cable 75 cm long
Assembly from above using assembly
Loosable plug connection for tankering
Optimal in interaction with Votronic filling displays
The tanker is compatible with the following Votronic :.
Wastewater indicator S, 5313
Fecal tank advertisement S, 5315
Info Panel Pro, 5330
Info Panel Pro 24V
VPC Terra
VPC Merkur
VPC Jupiter 100 Smart Shunt, 5747
VPC Jupiter 200 Smart Shunt, 5748
VPC Jupiter 400 Smart Shunt, 5749
Solid measurement technology and simple assembly
The tank electrode 20 K-WC was further developed on the basis of the long-proven tank electrode in order to obtain a full filler indicator especially for use in cassette toilets. The compact design makes it possible to simply screw the tanker into the toilet cassette from above via the supplied assembly ring. The necessary assembly opening of 38 mm diameter is easy to produce with a hole saw. The fully resumed electronics is designed waterproof (IP67) and suitable for rough operation when rinsing the toilet cassette.
To change the cassette, the tank electrode 20 K-WC is separated from the vehicle via a solid 3-pin round connector and the plug on the cassette is fixed. In addition to the 3-pin round plug connection, the scope of delivery also includes assembly and complete assembly material.
Delivery time: 1-3 working days
Scope of delivery:
1x votronic 5555 tank electrode 20 K toilet
010002110
PHILIPPI shore connection unit LAE 211
Shore connection unit for mains power takeover 230V/50Hz with Schuko socket. Mains control lamp shows mains status. Internal mains connection directly to the terminals of the RCBO circuit breaker, cable entry with PG screw connection. Splash-proof all-plastic housing with hinged lid. Degree of protection IPX4.
Power indicator light
RCBO circuit breaker 16A/0.03A 2-pole
Dimensions: W 97 x H 246 x D 97mm
8EV 003 361-002
Hella two -level fan turbo 12V black
Hella Marine - two -level fan "Turbo"
Universal fan of the proven, versatile "Turbo" series.
Alignable and determined on all sides.
- Quality engine, guarantee for extreme running and long lifespan
- 150 mm diameter with protective grille
- up to 95 liters/sec air power with low power consumption
- Two-stage switch in front of the protective grille
- side, standing or hanging assembly possible
Material description
Pagan plastic
Switch
2 stages on the device
Performance
Level 1: 70 liters / sec
Level 2: 95 liters / sec
Power consumption
6.5 W
installation
Incl. 1.4 m connecting cable