Caravan Mover Power Packs

Filter
Not in stock
CSX12080-040MSet
CS Lithium Lifepo4 Mover Power Pack Set 12.8V / 40AH / PB -EQ 80AH - ~ 6.5kg with charger
40AH Lithium Mover Power Pack installation with charger The Mover Power Pack Set solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 60 minutes. They also have a safe supply function for lighting and inverters up to 1000W. Top features: Light weight, super light Very high security 100% maintenance -free Replaces an 80Ah lead / gel / AGM battery Persistent shunting operation Additional power supply More than 10 years of service life Complete set The Lithium Power Pack Set is the ideal power supply for your caravan with enormous weight savings. We also offer 3 different batteries to choose from, 20Ah, 40AH and 60AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features:   Lithium battery with battery management system Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time Inclusive battery charging cable Inclusive main switch Including fast pole terminals Application The sets consists of a lithium iron phosphate battery with suitable lithium charger, charging cable, dividing switch and fast-moving clamps. The system can be loaded via a power connection at the campsite. The lithium charger automatically switches off after full charging without further charging maintenance. If you want a charge while driving, the battery can connect to your motorhome charging system. It is also possible that the battery is connected to a solar controller. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current Motor vehicle connection for inverter with max. 100A permanent current / 750a peak Charging cable with a spotted XT60 plug Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 service The system works automatically and does not have to be activated. The XF3 lithium charger loads the battery to 14.6V and switches on automatically when energy is removed from the battery. For wintering, we recommend disconnecting the vehicle clamps for a standing time up to 6 months without any charge. Bluetooth Our batteries deliberately do not offer a Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by the supplied charger at the campsite. A status indicator is not precise with lithium batteries via Bluetoots without a measurement shunt, since the voltage drop as is not the case with the old lead technology. For a really accurate level indicator, we therefore recommend installing a measuring shunt with 100A.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 40AH / PB-EQ 80AH 1 x lithium lifepo4 charger with a mains connection cable 1 x charging cable 2 x quick pole terminals for plus and minus pole 1 x main switch 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12080-040MSet Type:Mover battery Nominal capacity: 40Ah Energy content: 480Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 80Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 40A Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 100a Maximum inver power: 750a Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 4.2kg (set) Dimensions (BXTXH): 279 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€569.00* €749.00*
Small amount
CSX12120-060M
CS Lithium Lifepo4 Mover Power Pack 12.8V / 60AH / PB -EQ 120AH - ~ 8.6kg
60Ah Lithium Mover Power Pack Battery The Mover Power Pack Battery solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 180 minutes. In addition, you have a safe supply function for lighting and inverter up to 1000W permanent output. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 120Ah lead / gel / AGM battery Persistent shunting operation Additional power supply More than 10 years of service life   The lithium power pack battery is the ideal power supply for your caravan with enormous weight savings. We also offer 4 different batteries to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Construction of the lithium battery with battery management system (BMS) Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time   Application The lithium-iron phosphate battery can be installed in residential cars with existing charging technology if the installed charger can be converted to lithium or lead-acid as a battery type. The same applies to the loading via solar. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current / 750a lace Motor vehicle connection for inverter with max. Peak1000W continuous output / 2000W peak output Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 wintering The self-discharge of the Lithium Mover Power Pack Battery is very low compared to conventional batteries with 1-3% so that we only recommend disconnecting the battery for wintering. Bluetooth Our batteries deliberately do not offer a Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by your charger. A status display purely via Bluetooths without a measurement shunt is also not exactly with lithium batteries, since the voltage drop as is not the case with the old lead technology.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 60AH / PB-EQ 120AH 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12120-060MSet Type:Mover battery Nominal capacity: 60Ah Energy content: 720Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 120Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 60a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power: 2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 8.6kg Dimensions (BXTXH): 355 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€699.00* €924.00*
Small amount
CSX12120-060MSet
CS Lithium Lifepo4 Mover Power Pack Set 12.8V / 60AH / PB -EQ 120AH - ~ 9.1kg with charger
60AH Lithium Mover Power Pack incorporation set with LIFEPO4 charger The Mover Power Pack Set solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 180 minutes. They also have a safe supply function for lighting and inverters up to 1000W. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 120Ah lead / gel / AGM battery Constant maneuvering operations Additional power supply More than 10 years of service life Complete set The Lithium Power Pack Set is the ideal power supply for your caravan with enormous weight savings. We also offer 3 different batteries to choose from, 20Ah, 40AH and 60AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Lithium battery with battery management system Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time Inclusive battery charging cable Inclusive main switch Including fast pole terminals Application The sets consists of a lithium iron phosphate battery with suitable lithium charger, charging cable, dividing switch and fast-moving clamps. The system can be loaded via a power connection on the champing place. The lithium charger automatically switches off after the full store without further charging maintenance. If you want a charge while driving, the battery can connect to your motorhome charging system. It is also possible that the battery is connected to a solar controller. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current Motor vehicle connection for inverter with max. 100A permanent current / 750a peak Charging cable with a spotted XT60 plug Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 service The system works automatically and does not have to be activated. The XF3 lithium charger loads the battery to 14.6V and switches on automatically when energy is removed from the battery. For wintering, we recommend disconnecting the vehicle clamps for a standing time up to 6 months without any charge. Bluetooth Our batteries do not offer Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by the supplied charger at the campsite. A status display is not precisely via Bluetooth without a measurement shunt for lithium batteries, since the voltage drop as is not the case with the old lead technology. For a really accurate level indicator, we therefore recommend installing a measuring shunt with 100A.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 60AH / PB-EQ 120AH 1 x lithium lifepo4 charger with a mains connection cable 1 x charging cable 2 x quick pole terminals for plus and minus pole 1 x main switch 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12120-060MSet Type:Mover battery Nominal capacity: 60Ah Energy content: 720Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 120Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 60a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power: 2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 9.1kg (set) Dimensions (BXTXH): 355 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€779.00* €999.00*
Not in stock
CSX12160-080MSet
CS Lithium Lifepo4 Mover Power Pack Set 12.8V / 80AH / PB -EQ 120AH - ~ 11.1kg with charger
80AH Lithium Mover Power Pack built in with Lifepo4 charger The Mover Power Pack Set solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 240 minutes. They also have a safe supply function for lighting and inverters up to 1000W. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 160AH lead / gel / AGM battery Persistent shunting operation Additional power supply More than 10 years of service life Complete set The Lithium Power Pack Set is the ideal power supply for your caravan with enormous weight savings. We also offer 3 different battery sizes to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Lithium battery with battery management system Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time Inclusive battery charging cable Inclusive main switch Including fast pole terminals Application The sets consists of a lithium iron phosphate battery with suitable lithium charger, charging cable, dividing switch and fast-moving clamps. The system can be loaded via a power connection on the champing place. The lithium charger automatically switches off after the full store without further charging maintenance. If you want a charge while driving, the battery can connect to your motorhome charging system. It is also possible that the battery is connected to a solar controller. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current Motor vehicle connection for inverter with max. 100A permanent current / 750a peak Charging cable with a spotted XT60 plug Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 service The system works automatically and does not have to be activated. The XF3 lithium charger loads the battery to 14.6V and switches on automatically when energy is removed from the battery. For wintering, we recommend disconnecting the vehicle clamps for a standing time up to 6 months without any charge. Bluetooth Our batteries do not offer Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by the supplied charger at the campsite. A status display is not precisely via Bluetooth without a measurement shunt for lithium batteries, since the voltage drop as is not the case with the old lead technology. For a really accurate level indicator, we therefore recommend installing a measuring shunt with 100A.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 80AH / PB-EQ 160AH 1 x lithium lifepo4 charger with a mains connection cable 1 x charging cable 2 x quick pole terminals for plus and minus pole 1 x main switch 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12160-080MSet Type:Mover battery Nominal capacity: 80Ah Energy content: 960Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 160Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 80a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 100a Maximum inver power: 750a Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 11.1kg (set) Dimensions (BXTXH): 355 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€879.00* €1,124.00*
Not in stock
CSX12080-040M
CS Lithium Lifepo4 Mover Power Pack 12.8V / 40AH / PB -EQ 80AH - ~ 6.0kg
40AH Lithium Mover Power Pack Battery The Mover Power Pack Battery solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 60 minutes. You also have a secure supply function for lighting and inverter up to 1000W permanent output. Top features: Light weight, super light Very high security 100% maintenance -free Replaces an 80Ah lead / gel / AGM battery Constant maneuvering operations Additional power supply More than 10 years of service life   The lithium power pack battery is the ideal power supply for your caravan with enormous weight savings. We also offer 4 different batteries to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Construction of the lithium battery with battery management system (BMS) Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time   Application The lithium-iron phosphate battery can be installed in residential cars with existing charging technology if the installed charger can be converted to lithium or lead-acid as a battery type. The same applies to the loading via solar. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current / 750a lace Motor vehicle connection for inverter with max. Peak1000W continuous output / 2000W peak output Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 wintering The self-discharge of the Lithium Mover Power Pack Battery is very low compared to conventional batteries with 1-3% so that we only recommend disconnecting the battery for wintering. Bluetooth Our batteries deliberately do not offer a Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by your charger. A status display purely via Bluetooths without a measurement shunt is also not exactly with lithium batteries, since the voltage drop as is not the case with the old lead technology.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 40AH / PB-EQ 80AH 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12080-040MSet Type:Mover battery Nominal capacity: 40Ah Energy content: 480Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 80Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 40A Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power: 2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 6.0kg Dimensions (BXTXH): 279 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€519.00* €674.00*
Small amount
PPP012040000
Victron PPP-40 Peak Power Pack 12.8V/40AH 512Wh
The PPP-40 12.8V 40AH (MPN PPP012040000) from Victron Energy is a mobile lithium-ion memory solution based on its own-safe Li-Fepo4 cells. With a nominal capacity of 40AH, the PPP-40 is the largest member of the Peak Power Pack family of Victron. With a nominal voltage of 12.8V, the battery pack 512WH offers energy for on the go. In addition to a very low self-discharge, this power pack also shines with an excellent top output current performance. Important performance features of the Peak power pack PPP-40 40AH: Low weight with only 8.6kg, therefore ideal for the outdoor area 40AH (= 512Wh) storage capacity, 12.8V nominal voltage-integrated warehouse mode prevents deep discharge in the case of long-term storage Exit 1: Integrated (shunting aid) high-current output e.g. for maneuvering aid from small followers Exit 2: output for 12V DC current consumers with low electricity requirements (max. 30A) Based on the latest Lifepo4 cell technology has a built -in charger for charging with 230V network current Entrance 1: Can be operated by different DC current sources such as solar panels as long as these correspond to the current input specifications (see data sheet) Entrance 2: 230V network connection for charging such as network electricity offers high security even with improper use Resistant to deep discharge and insufficient charging Also possible load via vehicle battery at the entrance 1 Remote-controlled on/off and switch off and status display Ve.direct for coupling with the smartphone or computer (optional accessories required) Solid performance in solar and other applications? Is ideal in applications in which the charging current can be very irregular, as is the case, for example, in the solar sector. Deep discharge and inadequate charging, or irregular cycles, would quickly harm a conventional lead-acid battery. For the PPP-40 Peak Power Pack 40AH based on Lifepo4, however, such a use does not make a problem. Smarter energy storage: Ve.direct compatible? You can use the integrated VE.Direct connection to your Peak Powerpack 40AH 12.8V via the optional available Bluetooth Smart Dongle Connect to your app capable smartphone or tablet. Alternatively, the VE.Direct to USB Interface Cable can also be connected to connect the Power Pack to the computer or notebook. Important technical features of the PPP-40 40AH 12.8V power pack: Weight: 8.6kg Dimensions: 212 x 190 x 172 mm Monitoring and control: via the included print button with 2 LEDs Communication: About integrated VE.Direct connection Scope of delivery: 1x Victron Energy Peak Power Pack PPP-40 12.8V 40AH 512, WH, MPN PPP012040000 1x assembly strap 1x power adapter 1x power cable 1x print button with cable (2 m) and two -colored LED 1x operating instructions Weight 8.6 kg Manufacturer Victron Energy Product Lifepo4 battery
€684.00* €934.15*
Small amount
CSX12040-020MSet
CS Lithium Lifepo4 Mover Power Pack Set 12.8V / 20AH / PB -EQ 40AH - ~ 4.2kg with charger
20Ah lithium mover power pack installation With lifepo4 charger The Mover Power Pack Set solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 30 minutes. You also have a secure supply function for lighting and inverter up to 1000W permanent output. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 40Ah lead / gel / AGM battery Constant maneuvering operations Additional power supply More than 10 years of service life Complete set The Lithium Power Pack Set is the ideal power supply for your caravan with enormous weight savings. We also offer 4 different batteries to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Lithium battery with battery management system (BMS) Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time Inclusive battery charging cable Inclusive main switch Including fast pole terminals Application The sets consists of a lithium iron phosphate battery with suitable lithium charger, charging cable, dividing switch and fast-moving clamps. The system can be loaded via a power connection on the champing place. The lithium charger automatically switches off after the full store without further charging maintenance. If you want a charge while driving, the battery can connect to your motorhome charging system. It is also possible that the battery is connected to a solar controller. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical network with max. 100A permanent current Motor vehicle connection for inverter with max. 1000W permanent current / 2000W top current Charging cable with a spotted XT60 plug Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 service The system works automatically and does not have to be activated. The XF3 lithium charger loads the battery to 14.6V and switches on automatically when energy is removed from the battery. For wintering, we recommend disconnecting the vehicle clamps for a standing time up to 6 months without any charge. Bluetooth Our batteries do not offer Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by the supplied charger at the campsite. A status indicator is not precise with lithium batteries via Bluetoots without a measurement shunt, since the voltage drop as is not the case with the old lead technology. For a really accurate level indicator, we therefore recommend installing a measuring shunt with 100A.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 20Ah / PB-EQ 40AH 1 x lithium lifepo4 charger with a mains connection cable 1 x charging cable 2 x quick pole terminals for plus and minus pole 1 x main switch 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12040-020MSet Type:Mover battery Nominal capacity: 20Ah Energy content: 240Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 40Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 20a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power: 2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 4.2kg (set) Dimensions (BXTXH): 279 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€489.00* €624.00*
Available (more than 10)
CSX12040-020M
CS Lithium Lifepo4 Mover Power Pack 12.8V / 20AH / PB -EQ 40AH - ~ 3.6kg
20Ah Lithium Mover Power Pack Battery The Mover Power Pack Battery solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 30 minutes. You also have a secure supply function for lighting and inverter up to 1000W permanent output. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 40Ah lead / gel / AGM battery Constant maneuvering operations Additional power supply More than 10 years of service life   The lithium power pack battery is the ideal power supply for your caravan with enormous weight savings. We also offer 4 different batteries to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Construction of the lithium battery with battery management system (BMS) Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time   Application The lithium-iron phosphate battery can be installed in residential cars with existing charging technology if the installed charger can be converted to lithium or lead-acid as a battery type. The same applies to the loading via solar. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current / 750a lace Motor vehicle connection for inverter with max. Peak1000W continuous output / 2000W peak output Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 wintering The self-discharge of the Lithium Mover Power Pack Battery is very low compared to conventional batteries with 1-3% so that we only recommend disconnecting the battery for wintering. Bluetooth Our batteries deliberately do not offer a Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by your charger. A status display purely via Bluetooths without a measurement shunt is also not exactly with lithium batteries, since the voltage drop as is not the case with the old lead technology. Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 20Ah / PB-EQ 40AH 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12040-020MSet Type:Mover battery Nominal capacity: 20Ah Energy content: 240Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 40Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 20a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power:2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 3.6kg Dimensions (BXTXH): 279 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€429.00* €549.00*
Not in stock
PPP012020000
Victron PPP-20 Peak Power Pack 12.8V/20AH 256Wh
The PPP-20 12.8V 20AH (MPN PPP012020000) from Victron Energy is a mobile lithium-ion memory solution based on own-safe Li-Fepo4 cells. With a nominal capacity of 20Ah, the PPP-20 is the second smallest member of the Peak Power Pack family of Victron. With a nominal voltage of 12.8V, the battery pack 256Wh offers energy for on the go. In addition to a very low self-discharge, this power pack also shines with an excellent top output current performance. Important performance features of the Peak power pack PPP-20 20AH: Low weight with only 3.8kg, therefore ideal for the outdoor area 20AH (= 256Wh) storage capacity, 12.8V nominal voltage-integrated warehouse mode prevents deep discharge in the case of long-term storage Exit 1: Integrated (shunting aid) high-current output e.g. for maneuvering aid from small followers Exit 2: output for DC current consumers with low electricity requirements (max. 30A) Based on the latest Lifepo4 cell technology has a built -in charger for charging with 230V network current Entrance 1: Can be operated by different DC current sources such as solar panels as long as these correspond to the current input specifications (see data sheet) Entrance 2: 230V network connection for charging such as network electricity offers high security even with improper use Resistant to deep discharge and insufficient charging Also possible load via vehicle battery at the entrance 1 Remote-controlled on/off and switch off and status display Ve.direct for coupling with the smartphone or computer (optional accessories required) Solid performance in solar and other applications Is ideal in applications in which the charging current can be very irregular, as is the case, for example, in the solar sector. Deep discharge and inadequate charging, or irregular cycles, would quickly harm a conventional lead-acid battery. For the PPP-20 Peak Power Pack 20AH based on Lifepo4, however, such a use does not make a problem. Smarter energy storage: Ve.direct compatible You can connect your Peak Powerpack 20AH 12.8V to the optionally available Bluetooth Smart Dongle to your app capable smartphone or tablet via the integrated VE.Direct connection. Alternatively, the VE.Direct to USB Interface Cable can also be connected to connect the Power Pack to the computer or notebook. Important technical features of the PPP-20 20AH 12.8V power pack: Weight: 3.8kg Dimensions: 132 x 190 x 172mm Monitoring and control: via the included print button with 2 LEDs Communication: About integrated VE.Direct connection   Scope of delivery: 1x Victron Energy Peak Power Pack PPP-20 12.8V 20AH, PPP012020000 1x assembly strap 1x power adapter 1x power cable 1x print button with cable (2 m) and two -colored LED 1x operating instructions data sheet Generally item number 2-67-010005 Manufacturer part number PPP012020000 Product Lifepo4 battery Manufacturer Victron Energy Weight 3.8 kg EAN 8719076017318
€394.06* €537.88*
Not in stock
CSX12160-080M
CS Lithium Lifepo4 Mover Power Pack 12.8V / 80AH / PB -EQ 120AH - ~ 10.6kg
80AH Lithium Mover Power Pack Battery The Mover Power Pack Battery solves its maneuvering problems and also supplies your caravan with electricity with self -sufficient use. The LIFEPO4 battery lithium provides the required high current for powerful maneuvering up to 240 minutes. In addition, you have a safe supply function for lighting and inverter up to 1000W permanent output. Top features: Light weight, super light Very high security 100% maintenance -free Replaces a 160AH lead / gel / AGM battery Persistent shunting operation Additional power supply More than 10 years of service life   The lithium power pack battery is the ideal power supply for your caravan with enormous weight savings. We also offer 4 different batteries to choose from, 20AH, 40AH, 60AH and 80AH. The larger the battery, the longer you can stand self -sufficient, the maneuvering performance is not affected. More features: Construction of the lithium battery with battery management system (BMS) Deep discharge Short -circuit -resistant / spotty -proof Cell balancing Load monitoring by frost-cell control Overload No risk of fire and explosion Fixed assembly, no expansion for wintering necessary 6 months off-line warehouse time   Application The lithium-iron phosphate battery can be installed in residential cars with existing charging technology if the installed charger can be converted to lithium or lead-acid as a battery type. The same applies to the loading via solar. Security The battery cells are completely protected by the battery management system (BMS) built into the battery. This does not make the feared deep discharge. Connections: MOVER TO PLATION THE MOVER with 750a peak electricity Motor vehicle connection for electrical system with max. 100A permanent current / 750a lace Motor vehicle connection for inverter with max. Peak1000W continuous output / 2000W peak output Application for the following maneuvering systems possible: Truma Mover SX, Truma Mover XT, Truma Mover XT2, Truma Mover XT4 Al-Ko Mammut 115/220, Ranger 115/226, Mammut M20 Rich Easydriver pro and active Sanding aid GO2 wintering The self-discharge of the Lithium Mover Power Pack Battery is very low compared to conventional batteries with 1-3% so that we only recommend disconnecting the battery for wintering. Bluetooth Our batteries deliberately do not offer a Bluetooth interface. In order to avoid a long lifespan and an empty of the battery by small but constant consumers, we do not install a Bluetooth. The system works perfectly and is safely loaded by your charger. A status display is not precisely via Bluetooth without a measurement shunt for lithium batteries, since the voltage drop as is not the case with the old lead technology.   Scope of delivery / The set consists of: 1 x lithium lifepo4 Power Pack 80AH / PB-EQ 160AH 1 x installation instructions Certificates: CE: General operational safety Unt38.3: Certified transport security in traffic Rohs: Certified material security Warranty: 2 years Technical specifications: Model: CSX12160-080MSet Type:Mover battery Nominal capacity: 80Ah Energy content: 960Wh Cell technology: Lithium-iron nanophosphate lifepo4 Cell type: A123 Systems Replaces one: 160Ah lead-gel-agm battery Application: 12V maneuvering systems, power supply, short -term high -flow laserations Application in parallel circuit: No Application Series circuit: No Operating voltage: 10.5 - 14.6V Nominal voltage: 13.2V Lifespan: => 10 years Cycling time at 80% DOD: = 3000 Cycling time at 50% DOD: = 5000 Loading programs: CCCV Load closing voltage: 14.6V Maximum charging current: 80a Permanent enthusiasm: 100a Peak enthusiast (1 sec.): 750a (s) Permanent inverter: 1000W Maximum inver power: 2000W Discharge tension: 10.5V Temperature range (discharge): -20 ° C to +65 ° C Temperature range (charge): 0 ° C to +50 ° C (BMS controlled) Temperature range (storage): -20 ° C to +65 ° C Battery management system (BMS): Yes, installed Connection solar controller: Yes / 12-14.6V Balancer: Yes, active balancer Self -discharge: 1-2% / month Installation position: any Connection: Standard vehicle pole terminal / polar order 0 Weight: 10.6kg Dimensions (BXTXH): 355 x 175 x 189 mm Light, strong, mobile, self -sufficient and safe!
€819.00* €1,049.00*
Small amount
PPP012030000
Victron PPP-30 Peak Power Pack 12.8V/30AH 384Wh
The PPP-30 12.8V 30AH (MPN PPP012030000) from Victron Energy is a mobile lithium-ion memory solution based on own-safe Li-Fepo4 cells. With a nominal capacity of 30Ah, the PPP-30 is the second smallest member of the Peak Power Pack family of Victron. With a nominal voltage of 12.8V, the battery pack 384Wh offers energy for on the go. In addition to a very low self-discharge, this power pack also shines with an excellent top output current performance. Important performance features of the peak power pack PPP-30 30AH: Low weight with only 3.8kg, therefore ideal for the outdoor area 30AH (= 384Wh) storage capacity, 12.8V nominal voltage-integrated warehouse mode prevents to be discharged with long-term storage Exit 1: Integrated (shunting aid) high-current output e.g. for maneuvering aid from small followers Exit 2: output for 12V DC current consumers with low electricity requirements (max. 30A) Based on the latest Lifepo4 cell technology has a built -in charger for charging with 230V network current Entrance 1: Can be operated by different DC current sources such as solar panels as long as these correspond to the current input specifications (see data sheet) Entrance 2: 230V network connection for charging such as network electricity offers high security even with improper use Resistant to deep discharge and insufficient charging Also possible load via vehicle battery at the entrance 1 Remote-controlled on/off and switch off and status display Ve.direct for coupling with the smartphone or computer (optional accessories required) Solid performance in solar and other applications? Is ideal in applications in which the charging current can be very irregular, as is the case, for example, in the solar sector. Deep discharge and inadequate charging, or irregular cycles, would quickly harm a conventional lead-acid battery. For the PPP-30 Peak Power Pack 30AH based on Lifepo4, however, such a use does not make a problem. Smarter energy storage: Ve.direct compatible? You can use the integrated VE.Direct connection to your Peak Powerpack 30AH 12.8V via the optional available Bluetooth Smart Dongle Connect to your app capable smartphone or tablet. Alternatively, the VE.Direct to USB Interface Cable can also be connected to connect the Power Pack to the computer or notebook. Important technical features of the PPP-30 30AH 12.8V power pack: Weight: 5.4kg Dimensions: 172 x 190 x 172mm Monitoring and control: via the included print button with 2 LEDs Communication: About integrated VE.Direct connection Scope of delivery: 1x Victron Energy Peak Power Pack PPP-30 12.8V 30AH 384, WH, MPN PPP012030000 1x assembly strap 1x power adapter 1x power cable 1x print button with cable (2 m) and two -colored LED 1x operating instructions data sheet Weight 5.4 kg Manufacturer Victron Energy Product Lifepo4 battery    
€546.11* €747.32*