Network Chargers

Security for the battery The Votronic Automatic Charger, which are equipped with the latest charging technology and designed for all standard lead batteries, ensure the right battery charge (see chapter charging technology). The peripheral devices from Votronic are used to treat the batteries in daily operation, which work in the background and ensure automated loading control and battery monitoring. In the case of motorhomes, boats, emergency vehicles etc. Therefore, several batteries are usually installed in these vehicles, which are used separately after driving and standing. A distinction is made between the starter and supply battery (s). As the name suggests, one battery is responsible for the reliable start of the vehicle, while the other (s) takes over the supply of the electrical devices in the vehicle. In order for each battery circle to work reliably and the electrical concept of the vehicle works, various devices for loading control are used while driving. Device type Art.- No. Operating Tension [V] Electricity- recording [Ma] Switching current Tirriad Driving [A] Charging current in standing operation For starter batt. [A] Weight [G] execution Standby-Charger 12V 3065 12 - - 0 - 3 52 A Standby-Charger 24V 6065 24 - - 0 - 2 52 B Dimensions (W x D x H): 90 x 60 x 38 mm Test mark: CE, e-test (EMV/car directive) Scope of delivery: Instructions Standby-Charger The Votronic Standby Charger serves to automatically recharge and load the starter battery or the additional battery if the network charger, the solar loader or the generator only has a charging output. The device can be easily retrofitted by simply switching between the on-board and start battery or on-board and additional battery without having to change the existing cabling. For example, if the network charger is in operation and loads the on-board battery, the second battery (start battery or additional battery) is also included with a small part of the charging current. This loading is automatically working and can be seen by an increased voltage situation of the second battery. An overload of the second battery is excluded because the charging voltage is lowered by at least 0.6V and the charging current is limited to 3a (24V variant: 2a). Make sure that both batteries Same battery tension 12 V / 12 V or 24 V / 24 V, since a mixed operation is not possible 12 V and 24 V. The standby charger is Only for use with lead batteries Suitable (acid / gel / AGM technology), not for the combination of lifepo4 and lead (starter) batteries. Also available in boats with the electronics protected from moisture! Delivery time: 1-3 working days  

Das Blue Smart IP65 12/15 12V 230V Batterieladegerät ist das neuste professionelle, Ladegerät von Victron Energy mit eingebautem Bluetooth. Es ist zum aufladen von 12V Batterien verschiedenster Bauarten ausgelegt und lieferten einen maximalen Ladestrom von 15A. Zusammen mit der kostenlosen VictronConnect App können Sie so die Aktivität Ihres Batterieladers einfach und smart über Ihr Smartphone, Tablet oder den Computer auswerten und sogar bis zu einem gewissen Grad konfigurieren.Technische Highlights des Blue Smart IP65 12/15 Batterieladegeräts einfache Konfiguration und Einrichtung des Blue Smart IP65 12/15 über Bluetooth Schnittstelle für alle 12V Batterie-Typen geeignet max. 15A Ladestrom solider Schutz gegen Spritzwasser. Staub- und Chemikalien dank Schutzart IP65 verfügt über mehrere Funktionen zur Verlängerung der Batterielebensdauer automatischer Temperatur Abgleich bei niedrigen, bzw. hohen Temperaturen automatische Stromversorgungsfunktion 7-stufiger, intelligenter Ladealgorithmus kann vollständig entladene Batterien „tote Batterien“ wiederherstellen verfügt über Niedrigenergiemodus zum Laden kleiner Batterien Victron-Artikelnummer: BPC121531064R Lithium-Ionen Batteriemodus Ultra-hocheffzientes “grünes” BatterieladegerätMit einem Wirkungsgrad von bis zu 95 % erzeugen diese Ladegeräte drei- bis viermal weniger Wärme, als der Industriestandard. Und, nachdem die Batterie voll aufgeladen ist, reduziert sich der Stromverbrauch auf 0,5 Watt, das ist fünf- bis zehnmal besser, als der Industriestandard.langlebig, sicher und leise geringe Wärmebelastung der elektronischen Bauteile geschützt gegen das Eindringen von Staub, Wasser und Chemikalien. Schutz vor Überhitzung: Der Ausgangsstrom wird linear verringert , wenn die Temperatur auf bis zu 60 °C ansteigt, das Ladegerät versagt also auch nicht bei extremen Temperaturen die Ladegeräte sind absolut geräuschlos dank passiver Kühlung: kein Lüfter oder anderen beweglichen Teile Reconditioning (Wiederherstellung)Eine Blei-Säure-Batterie. die nicht ausreichend geladen wurde oder tage- bzw. wochenlang im entladenen Zustand belassen wurde, verschlechtert ihre Leistung aufgrund von Sulfatierung. Sofern der Prozess rechtzeitig gestoppt wird, lässt sie die Sulfatierung teilweise wieder rückgängig machen, indem die Batterie mit niedrigem Strom geladen wird, bis eine höhere Spannung erreicht wurde.Funktion zur Wiederherstellung von vollständig entladenen BatterienDie meisten Ladegeräte mit Verpolungsschutz erkennen eine Batterie, die bis auf Null Volt oder fast auf Null Volt entladen wurde, nicht und laden sie daher auch nicht wieder auf. Das Blue Power-Ladegerät versucht jedoch, eine vollständig entladene Batterie mit niedrigem Strom wieder aufzuladen und nimmt den normalen Ladevorgang wieder auf, nachdem ausreichend Spannung über den Batterieanschlüssen aufgebaut wurde.Optionales Zubehör Blue Smart IP 65 12/15 BPC121531064R 12 V Zigarettenanzünderstecker mit Sicherung   2 Meter Verlängerungskabel Anschlussklemmen mit Sicherungen               M6 Kabelschuh-Steckverbinder mit Sicherung Lieferumfang: 1x Victron BPC121531064R Blue Smart IP65 12/15 12V 230V Batterieladegerät1x Bedienungsanleitung1x Anschlussklemmen1x M8 Kabelschuh-Steckverbinder

The Blue Smart IP22 12/30 (1) charger from Victron Energy (MPN BPC123047002) is a professional, compact 12V 30A battery charger of the latest generation with a charging output and built -in Bluetooth! The Blue Smart IP22 12/30 (1) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 12V lead batteries and modern lithium batteries. Highlights of the 12/30 (1) Blue Smart IP22 Charger Intelligent charging until the perfect battery state ... The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life. Restoration of deep-downloaded "dead" batteries Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections. Call the battery status from afar, with the VictronConnect app The Blue Smart IP22 12/30 (1) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. The most important technical features of the 12/30 (1) Blue Smart IP22 Charger Victron part number: BPC123042002 Lades 12V lead-acid, gel, agm and lithium batteries 30a maximum charging current 1 battery charging output Very compact dimensions: 235 x 108 x 65mm Highly modern, seven-level loading algorithm With integrated Bluetooth for use with the free VictronConnect app Other performance features of the 12/30 (1) Blue Smart IP22 battery loader Trend -setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard. Adaptive 7-stable loading algorithm The 12/30 (1) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. “Adaptive” means that the loading process is automatically adjusted to the type of battery use. Storage mode: Less maintenance and aging in the resting state of the battery The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 12V battery) in order to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Scope of delivery: 1x Victron Energy BPC123042002 12/30 (1) IP22 Blue Smart Charger 1x operating instructions data sheet Generally item number 1-67-010615 EAN 8719076037453 Manufacturer part number BPC123047002 Manufacturer Victron Dimensions (LXBXH) 10.8 x 23.5 x 6.5 cm Weight 0.9 kg

The Blue Smart IP 67 12/25 12V 230V battery charger from Victron Energy (MPN BPC122513006) is a smart, high-performance battery charger of the latest generation with 25a charging current for charging 12V AGM, gel and lyricic acid batteries as well as lithium ion batteries. In terms of function, the Blue Smart IP67 series is identical to the chargers of the Blue Smart IP 65 and IP 22 device families. Only the application environment for which these chargers are designed differ. Thanks to the integrated Bluetooth, the Blue Smart IP 67 battery chargers offer a wireless solution for monitoring voltage and electricity, for adapting settings and updating the charger when new functions are available. Important features of the Blue Smart IP67 12/25 25a battery charging devices Victron part number: BPC122513006 Model description: Blue Smart IP 67 12/25 Max. Charging current: 25a For battery voltage: 12V DC For mains voltage: 180-265 VAC 45-65 Hz Completely covered: waterproof, push -in and fire -retardant Smart configuration and monitoring via integrated Bluetooth and free app adaptive, 5-stage loading algorithm extends the life of your batteries thanks to the integrated warehouse mode can be used to supply 12V consumers High quality housing made of cast aluminum Protection against application errors: Polation on battery (fuse), protection against over temperature, protection against the start of the start Completely covered: waterproof, shock -protected and fire -retardant ??Water, oil or dirt cannot damage the Blue Smart IP67 charger. The housing is made of cast aluminum and the electronics are covered with resin. One of the highest load efficiency of all time!? Set a new industrial standard: With an efficiency of at least 92 % or more, these chargers produce three to four times less heat. Adaptive 5-stage loading algorithm? The Blue Smart 12/25 IP67 charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the loading process is automatically adjusted to the type of battery use. "Bulk" (constant trump phase) "Absorption" (constant voltage phase) "Recondition" (regeneration phase) "Float" (loading tension phase) "Storage" (warehouse mode) Warehouse mode: Less maintenance and aging in the resting state of the battery The warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Significant differences to the Blue Smart IP 65 family The two device groups differ in the following points: The type of protection, the IP 67 devices have the best possible protection Blue Smart IP 65 devices have a 7-stage loading algorithm, with the IP67 it is 5-stated Delivery time: 1-3 working days Scope of delivery: 1x VICTRON BPC122513006 Blue Smart IP67 12/25 25a 12v 230V Battery charger 1x operating instructions 1x 1.5m battery connection cable red/black        

The Blue Smart IP22 12/15 (3) charger of Victron Energy (MPN BPC12154002), is a professional, compact 12V 15A battery charger of the latest generation with 3 charging outputs and built -in Bluetooth! The Blue Smart IP22 12/15 (3) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 12V lead batteries and modern lithium batteries. It offers Highlights of the 12/15 (3) Blue Smart IP22 Charger Intelligent charging until the perfect battery state ... The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life. Restoration of deep-downloaded "dead" batteries Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections. Call the battery status from afar, with the VictronConnect app The Blue Smart IP22 12/15 (3) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. The most important technical features of the 12/15 (3) Blue Smart IP22 Charger Victron part number: BPC121544002 Lades 12V lead-acid, gel, agm and lithium batteries 15a maximum charging current 3 battery charging outputs Very compact dimensions: 235 x 108 x 65mm Highly modern, seven-level loading algorithm With integrated Bluetooth for use with the free VictronConnect app Other features of the 12/15 (3) Blue Smart IP22 Batterieladers Trend -setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard. Adaptive 7-stable loading algorithm The 12/15 (3) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the loading process is automatically adjusted to the type of battery use. Storage mode: Less maintenance and aging in the resting state of the battery The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 12V battery) in order to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure.   Scope of delivery: 1x Victron Energy BPC121544002 12/15 (3) IP22 Blue Smart Charger 1x operating instructions IP protection IP22 EAN 8719076037422 Ambient temperature -20 ° C - +50 ° C Manufacturer part number BPC121544002 guarantee 2 years humidity Max. 98 %, not condensing Manufacturer Victron, Victron Energy Weight 1.3 kg Dimensions (LXBXH) 10.8 x 23.5 x 6.5 cm  

The Blue Smart IP 67 12/17 12v 230V battery charger from Victron Energy (MPN BPC121713006) is a smart, high-performance battery charger of the latest generation with 17A charging current for charging 12V AGM, gel and lead and leading batteries, such as lithium ions. In terms of function, the Blue Smart IP67 series is identical to the chargers of the Blue Smart IP 65 and IP 22 device families. Only the application environment for which these chargers are designed differ. Thanks to the integrated Bluetooth, the Blue Smart IP 67 battery chargers offer a wireless solution for monitoring voltage and electricity, for adapting settings and updating the charger when new functions are available. Important features of the Blue Smart IP67 12/17 17A battery charging device    Victron part number: BPC121713006  Model description: Blue Smart IP 67 12/17  Max. Charging current: 17a  For battery voltage: 12V DC  For mains voltage: 180-265 VAC 45-65 Hz  Completely covered: waterproof, shock -protected and fire -retardant  Smart configuration and monitoring via integrated Bluetooth and free app  adaptive, 5-stage loading algorithm  extends the life of your batteries thanks to the integrated warehouse mode  can be used to supply 12V consumers  High quality housing made of cast aluminum  Protection against application errors: Polation on battery (fuse), protection against over temperature, protection against the start of the start  Completely covered: waterproof, shock -protected and fire -retardant   Water, oil or dirt cannot damage the Blue Smart IP67 charger. The housing is made of cast aluminum and the electronics are covered with resin. One of the highest level of loading effects of all time! Set a new industrial standard: With an efficiency of at least 92 % or more, these chargers produce three to four times less heat. adaptive 5-stage loading algorithm The Blue Smart 12/17 IP67 charger is characterized by its microprocessor-controlled, "adaptive" battery management. “Adaptive” means that the loading process is automatically adjusted to the type of battery use.  "Bulk" (constant trump phase)  "Absorption" (constant voltage phase)  "Recondition" (regeneration phase)  "Float" (loading tension phase)  "Storage" (warehouse mode) Warehouse mode: Less maintenance and aging in the resting state of the battery The warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Significant differences to the Blue Smart IP 65 family The two device groups differ in the following points:  The type of protection, the IP 67 devices have the best possible protection  Blue Smart IP 65 Retäte have a 7-stage loading algorithm, in the IP67 it is 5-stated Scope of delivery: 1x VICTRON BPC121713006 Blue Smart IP67 12/17 17A 12V 230V Battery charger 1x operating instructions 1x 1.5m battery connection cable red/black Delivery time 1-3 working days   data sheet Dimensions (LXBXH) 6.5 x 21.9 x 9.9cm Weight 2.4 kg Manufacturer Victron Energy guarantee 5 years of manufacturer's guarantee Product Adaptive, 4-stage 230V-12V battery charger with smartphone connection and support of all common types of battery.

The Blue Smart IP22 12/15 (1) charger of Victron Energy (MPN BPC121542002), is a professional, compact 12V 15A battery charger of the latest generation with a charging output and built -in Bluetooth! The Blue Smart IP22 12/15 (1) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 12V lead batteries and modern lithium batteries. It offers Highlights of the 12/15 (1) Blue Smart IP22 Charger Intelligent charging until the perfect battery state ... The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life. Restoration of deep-downloaded "dead" batteries Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections. Call the battery status from afar, with the VictronConnect app The Blue Smart IP22 12/15 (1) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. The most important technical features of the 12/15 (1) Blue Smart IP22 Charger Victron part number: BPC121542002 Lades 12V lead-acid, gel, agm and lithium batteries 15a maximum charging current 1 battery charging output Very compact dimensions: 235 x 108 x 65mm Highly modern, seven-level loading algorithm With integrated Bluetooth for use with the free VictronConnect app Other features of the 12/15 (1) Blue Smart IP22 Batterieladers Trend -setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard. Adaptive 7-stable loading algorithm The 12/15 (1) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the loading process is automatically adjusted to the type of battery use. Storage mode: Less maintenance and aging in the resting state of the battery The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 12V battery) in order to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure.   Delivery time: 1-3 working days Scope of delivery: 1x Victron Energy BPC121542002 12/15 (1) IP22 Blue Smart Charger 1x operating instructions           IP protection IP22 EAN 8719076037460 Ambient temperature -20 ° C - +50 ° C Manufacturer part number 8719076037415 guarantee 2 years humidity Max. 98 %, not condensing Manufacturer Victron, Victron Energy Weight 1.3 kg Dimensions (LXBXH) 10.8 x 23.5 x 6.5 cm  

The Blue Smart IP22 12/30(3) charger from Victron Energy (MPN BPC123044002), is a professional, compact 12V 30A battery charger of the latest generation with 3 charging outputs and built-in Bluetooth! The Blue Smart IP22 12/30(3) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and campers and charges both classic 12V lead batteries and modern lithium batteries. It offers Highlights of the 12/30(3) Blue Smart IP22 Charger intelligent charging until the battery is in perfect condition... The seven-stage charging algorithm gets the most out of your battery. The charger provides the battery with the energy it needs, keeping it in a healthy state, ensuring better performance... and a longer life. Recovery from deeply discharged "dead" batteries Unlike most other brands and ranges, the Blue Smart IP22 charger will attempt to recharge a deeply discharged battery by forcing a low charge current on it. Normal charging will then resume as soon as there is sufficient voltage between the battery terminals. Remote battery status with the VictronConnect app The Blue Smart IP22 12/30(3) charger has built-in Bluetooth. This allows you to check the status of the charger and battery on a smartphone, tablet or laptop. All charger settings can be configured using the VictronConnect app. The main technical characteristics of the 12/30(3) Blue Smart IP22 Charger Victron part number: BPC123044002 charges 12V lead-acid, gel, AGM and lithium batteries 30A maximum charging current 3 battery charging outputs very compact dimensions: 235 x 108 x 65mm highly modern, seven-stage loading algorithm with integrated Bluetooth for use with the free VictronConnect app Other features of the 12/30(3) Blue Smart IP22 battery charger Trend-setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard. Adaptive 7-stage loading algorithm The 12/30(3) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the The charging process is automatically adapted to the type of battery usage. Storage mode: Less maintenance and aging when the battery is idle Storage mode is always activated if there is no discharge within 24 hours. The float charge voltage is then set to 2.2V/cell (13.2V for a 12V battery) to minimize gassing and thereby prevent corrosion on the positive plates. Once a week the voltage is increased to the gassing voltage level. This achieves a kind of equalization charge that prevents electrolyte stratification and sulfation - the two main reasons for premature battery failure. Scope of delivery: 1x Victron Energy BPC123044002 12/30(3) IP22 Blue Smart Charger 1x operating instructions degree of protection IP IP22 EAN 8719076037460 Ambient temperature -20°C - +50°C manufacturer part number BPC123044002 Warranty 2 years humidity max. 98%, non-condensing manufacturer Victron, Victron Energy weight 0.9 kg Dimensions (LxWxH) 10.8 x 23.5 x 6.5 cm .

The Blue Smart IP22 24/8 (1) charger of Victron Energy (MPN BPC240842002), is a professional, compact 24V 8A battery charger of the latest generation with a charging output and built -in Bluetooth! The Blue Smart IP22 24/8 (1) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 24V lead batteries and modern lithium batteries. It offers Highlights of the 24/8 (1) Blue Smart IP22 Charger Intelligent charging until the perfect battery state ... The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life. Restoration of deep-downloaded "dead" batteries Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections. Call the battery status from afar, with the VictronConnect app The Blue Smart IP22 24/8 (1) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. The most important technical features of the 24/8 (1) Blue Smart IP22 Charger Victron part number: BPC240842002 Lades 24V lead-acid, gel, agm and lithium batteries 8a maximum charging current 1 battery charging output Very compact dimensions: 235 x 108 x 65mm Highly modern, seven-level loading algorithm With integrated Bluetooth for use with the free VictronConnect app Other features of the 24/8 (1) Blue Smart IP22 Batterieladers Trend -setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard. Adaptive 7-stable loading algorithm The 24/8 (1) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the loading process is automatically adjusted to the type of battery use. Storage mode: Less maintenance and aging in the resting state of the battery The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 24V battery) in order to minimize gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Delivery time: 1-3 working days Scope of delivery: 1x Victron Energy BPC240842002 24/8 (1) IP22 Blue Smart Charger 1x operating instructions IP protection IP22 EAN 8719076037491 Ambient temperature -20 ° C - +50 ° C Manufacturer part number BPC240842002 guarantee 2 years humidity Max. 98 %, not condensing Manufacturer Victron, Victron Energy Weight 0.9 kg Dimensions (LXBXH) 10.8 x 23.5 x 6.5 cm  

The Automatic Charger PB 1220 SMT 2B from Votronic (MPN 3101) is a modern battery charger for mobile use. It has charging programs for gel, AGM, acidity and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main exit is 20a. In addition, there is a side charging output for the starter battery, which can also deliver 2A charging current. The device is suitable for batteries with a capacity of 80 AH - 145 Ah. Important features of the PB 1220 SMT 2B battery cador Reliably charges gel, AGM, acid and Lifepo4 battery 20a charging current, 2A charging current at the side charging output Official Votronic part number: 3101 Battery capacity (recommended): 80 Ah - 145 Ah Load options: 1 supply and 1 starter battery The charging voltage is free of tips and regulated so that an overload of the batteries is excluded. Fully automatic operation: The charger can be constantly connected to the battery and keeps it in full load. In the event of a network failure, the batteries will not be unloaded (separation by security switch). Lithium LIFEPO4-MAINTENANCE, Auto Wake Up, maintenance phase: Regular automatic activation of the battery cell balancing every 10 days to ensure the full load of the battery. Lead battery regeneration with long downtimes twice a week against harmful acidic layers. Parallel and buffer operation: With simultaneous consumption, the battery is charged or fully received. The adaptation of the loading times calculates and monitors the charger automatically. Monitoring-free charge: Multiple protection against overload, overheating, overvoltage, short circuit, polarity, misconduct and battery recharge through electronic stop to the complete separation of charger and battery with built-in safety switch. Connection for battery temperature sensor (accessories temperature sensor 825, item no. 2001): In the case of lead batteries (acidity, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, causes a better in cold Full loading of the weaker battery, in summer temperatures, unnecessary battery absorbing and thus battery stress is avoided. With LIFEPO4 batteries, the battery temperature sensor is required for the function: it serves battery protection at high and especially at low temperatures below 0 ° C. Silent Run function: At the push of a button noise-optimized way of working (night operation). Power supply function: enables consumers to be supplied without a battery (e.g. battery change). Charging cable compensation: Tension losses on the charging cables are automatically excavated. Construction network filter: Problem-free parallel operation with solar systems, wind and benzingen generators, alternators etc. on a battery. Charging aid for low -level lead batteries: gentle invitation to the (lead -acid, -gel, -gm) battery up to 8 V, then powerful support of the battery with any still switched on consumers. Separation of the B -batteries in the event of a power failure, overheating, misconduct (safety switch per charging output). Separate side charging output "S" for the support and maintenance charge of the vehicle starter battery. Overview of the loading programs of the PB 1220 SMT 2B "Gel": charging program for gel batteries, characteristic Iu1ou2ou3 tailored to closed, gas-density gel/dryfit batteries with a defined electrolyte, which generally need a higher loading level and longer U1 holding times to achieve short loading times with particularly high capacity storage and one to avoid long-term battery "starvation". "AGM": charging program for AGM/fleece batteries, characteristic Iu1ou2ou3 intended for loading closed, gas-density AGM (absorbent glass-mat) batteries in lead-fleece technology, which is a particularly high U1 level with coordinated holding times need for full charging and then a moderate U2 level to keep charging (plate and round cells technology). "Universal": charging program for lead-acid/wet/AGM batteries, characteristic line iu1ou2ou3 universal program for loading and loading acid batteries in vehicles (mixed mobile/stationary). And good acid mixture for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy duty batteries, as well as AGM batteries with a normal U1 level. "LIFEPO4": charging program for lithium batteries, characteristic Iu1ou2ou3 charging program matched to lithium-lifepo4 batteries with its own BMS and prescribed or built-in protective circuit. Lifetime advantageous charging level of 50-80% and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake Up function activates the batteries cell balancing. Scope of delivery: 1x Votronic 3101 PB 1220 SMT 2B battery charger 1x operating instructions (German)   Technical specifications:  Network voltage (network frequency 45 - 65 Hz) 110 V - 230 V  Network function voltage area, all types 85 V - 270 V, briefly 305 V (5 seconds)  Network voltage area for full charging power 180 V - 270 V  Network performance max. 330 W  Network performance recording at loading management 1.9 W  Active sinus-shaped power factor correction (Cosphi <= 1) Yes  Charging current approx. 110 V network voltage 18 A  Main charging output battery I  Battery native voltage lead/lifepo4 battery 12 V / 12 V-13.3 V  Selectable charging programs lead gel/AGM/acidity, lifepo4 4  Battery capacity (recommended) 80 Ah - 145 Ah  Battery capacity (after application, e.g. Lifepo4) 50 Ah - 230 Ah  Charging current main load, i-phase, 8 V to U1; 0-15.5 h 20 A  Loading/buffer/load current, regulated U1-U2-U3 phase 0 a - 20 a  Minimum battery voltage for the start of the load 0 V  Preliminary flow, lowest -download batteries 0 V - 8 V 10.0 a  Return current made of battery (power failure) <0.5 MA  Reset voltage (30 sec), battery type dependent 12.75 V / 13.25 V  Charging stress limit (protection of affiliated consumers) 15.0 V  External overvoltage shutdown (20 sec) 15.5 V  Tension <30 MV RMS  Charging timer 4-fold  Group/short circuit/back load/safety protection Yes  Safety timer per loading phase I-/U1-/U2- Yes  Lead battery regeneration with a long service life, 2x aw. 1 H Yes  Lifepo4 car Wake Up at a long time, 10 daily 0.5 h daily Yes  or Lifepo4 lithium rest conservation (seasonal company) Yes  Input for battery temperature sensor Yes  Power supply operation (e.g. further supply for battery changes) Yes  2. Sideline Vehicle Starter Battery II (registration output network)  Battery native voltage (lead) 12 V  Charging current or resilience as a registration output 0 a - 2 a  Group/short circuit/back load/safety protection Yes  Connection for remote control automatic charger Yes  Device installation position any  Temperature range -20 / +45 ° C  Speed ​​-controlled, temperature -controlled fan Yes  Gradual delegation of the charging capacity at over temperature Yes  Safety shutdown at overheating Yes  Fan noise lowering, night operation (Silent Run) Yes  Protection class / protection class I / IP21  Dimensions, Dimensions including fastening flanges/feet, without connections 228 x 139 x 74 mm  Weight 1280 g  Ambient conditions, humidity Max. 95 % RF, not condensing  Safety regulations EN 60335-2-29  Scope of delivery: network cable, operating instructions

The Phoenix Smart Charger 12/30 (1+1) IP43 from Victron Energy (MPN PSC123051085) is a powerful battery charger of the latest generation. The device is designed for 12V battery voltage and, in addition to the strong 30A main charging output, also offers a side charging output with 3a charging power for a starter battery. The Phoenix Smart Charger 12/30 (1+1) IP43 fits into the integrated Bluetooth module in which the Victron smart family is becoming increasingly becoming, which can be perfectly networked and can also be controlled centrally. In addition to the Bluetooth module, there is also a VE.Direct connection and a freely programmable relay. Optionally, the Smart Battery Sense to control the battery temperature compensation can also be connected. The proven five-stage loading algorithm and the possibility of programming its own charging algorithm make the Phoenix Smart Charger 12/30 (1+1) IP43 a universally applicable high-tec battery loader, which can optimally load almost every battery type. Perfect battery charger for boats and vehicles Phoenix smart battery charger devices that (1+1) contain in the model name have a main charging output, with a full charging current and a 3A ancillary charging output for charging starter batteries. These models are therefore particularly suitable for the mobile area. The Phoenix Smart models with (3) in the model designation were particularly developed with regard to the needs in the marine area and offer three full power outputs for charging 3 battery benches. Highlights of the Phoenix Smart Charger 12/30 (1+1) IP43 Integrated Bluetooth module Integrated VE.Direct connections 1x 30a main charging output and 1 further side charging output for starter batteries Automatic voltage compensation adaptive, five -stage loading algorithm Variable constant stress phase Eye all common types of battery Prevention of damage caused by gastroplating thanks Reduced aging through storage with storage mode Lifepo4 also charges and can be connected to a BMS via optocoupler Fully programmable loading algorithm Remote on/off can be used as a power source Technical features of the Phoenix Smart 12/30 (1+1) Victron part number: PSC123051085 Number of batteries: 1 + 1 (1 main output with full power + 1x starter battery (max. 3a load) Maximum nominal charging current: 30A, battery voltage: 12V High efficiency: 94% Protection class: IP43 (electronic components), IP22 (connection area) You can find more data with the technical data Three integrated technologies for all -round healthy batteries Variable constant voltage phase: always delivers the correct load of charges With a low battery discharge (e.g. a yacht connected to the country current), a short constant voltage phase is chosen to avoid an overload. After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged. Prevention of damage caused by excessive gastung: Batterysafe mode In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage. However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage climb after the gas voltage has been reached (see also the graphics in the brochure). Less maintenance and aging in the resting state of the battery: the storage mode The warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Also perfect for Lifepo4 battery The Phoenix Smart Charger 12/30 (1+1) IP43 can be attached to/out of control by a relay or an optocopper output with an open collector from a Li-ion BMS to a remote-controlled one/output port . Alternatively, voltage and electricity can also be ruled completely via Bluetooth. Ve.direct interface, bluetooth and programmable relay The Phoenix Smart Charger 12/30 (1+1) IP43 from VICTRON is ideal thanks to the VE.Direct ports for a wired data connection with a color control panel, a PC or other devices. Also note the VictronConnect app for Android and iOS, which you can use with any smartphone or tablet to be wireless and read out your Phoenix Charger via Bluetooth. Programmable relay can also be programmed via the VE.Direct interface or a Bluetooth-compatible device in order to trigger an alarm or other events. Required accessories Please note that an AC connection cable is required for the connection of the Phoenix Smart Charger 12/30 (1+1) IP43 to the power grid. This is not included. You can find the right connection cable here: Frenchman Energy Frenchman marine   scope of delivery 1x PSC123051085 Victron Phoenix Smart Charger 12/30 (1+1) IP43 1x AC cable clamp 1x operating instructions data sheet IP protection IP43 Communication sports Bluetooth, ve.direct EAN 8719076041900 Manufacturer part number PSC123051085 Ambient temperature -20 ° C - +60 ° C Battery voltage 12V Number of charging outputs 1 + 1 Battery type adjustable Acid, gel, AGM, LIFEPO4 Charging Adaptive battery management Protective functions Polation on the battery, output ceiling, over temperature guarantee 2 years Temperature compensation Yes, several options available humidity Max. 95 %, not condensing Manufacturer Victron Energy Weight 3.6 kg Dimensions (LXBXH) 24.9 x 18 x 10 cm

ThePhoenix Smart Charger 12/50 (1+1) IP43 120-240V from Victron Energy is a powerful battery charger of the latest generation. The device is designed for 12V battery voltage and, in addition to the strong 50A main charging output, also offers a secondary load output with 4a charging power for a starter battery.With the integrated Bluetooth module, the Phoenix Smart Charger 12/50 (1+1) IP43 fits into the ever increasing Victron smart family, which can be perfectly networked and can be controlled centrally. In addition to the Bluetooth module, there is also a VE.Direct connection and a freely programmable relay. Optionally, the Smart Battery Sense to control the battery temperature compensation can also be connected. The proven five-stage loading algorithm and the possibility of programming its own charging algorithm make the Phoenix Smart Charger 12/50 (1+1) IP43 optimally load into a universally usable high-tec battery loader of the almost every battery type. Perfect battery charger for boats and vehiclesPhoenix Smart Battery charger devices that (1+1) contain in the model name have a main charging output with full charging current and a 4A ancillary charging output for charging starter batteries. These models are therefore particularly suitable for the mobile area. The Phoenix Smart models with (3) in the model designation were particularly developed with regard to the needs in the marine area and offer three full power outputs for charging 3 battery benches. Highlights of the Phoenix Smart Charger 12/50 (1+1) IP43- Integrated Bluetooth module - Integrated VE.Direct connections - 1x 50a main charging output and 1 further side charging output for starter batteries - Automatic voltage compensation - adaptive, five -stage loading algorithm - Variable constant stress phase - Eye all common types of battery - Prevention of damage caused by gastroplating thanks - Reduced aging through storage with storage mode - Lifepo4 also charges and can be connected to a BMS via optocoupler - Fully programmable loading algorithm - Remote on/off - can be used as a power source Technical features of the Phoenix Smart 12/50 (1+1)- Number of batteries: 1 + 1 (1 main output with full power + 1x starter battery (max. 4A load) - Maximum nominal charging current: 50A, battery voltage: 12V - High efficiency: 94% - Protection class: IP43 (electronic components), IP22 (connection area) Three integrated technologies for all -round healthy batteriesVariable constant stress phase: Always delivers the correct charging quantityWith a low battery discharge (e.g. a yacht connected to the country current), a short constant voltage phase is chosen to avoid an overload. After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged. Prevention of damage caused by excessive gastung: The Batterysafe modeIn order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage. However, an excessive gas development towards the end of the constant trump phase is limited by the charger the speed of the voltage increase after the gas voltage has been reached (see also the graphics in the brochure). Less maintenance and aging in the resting state of the battery: The storage moduThe warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 12 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure.Perfect for Lifepo4 batteryThe Phoenix Smart Charger 12/50 (1+1) IP43 can be attached to an on/off control by a relay or an optocoppler output with an open collector from an Li-ion BMS to a remote-controlled one/output port becomes. Alternatively, voltage and electricity can also be ruled completely via Bluetooth.Ve.direct interface, bluetooth and programmable relayThe Phoenix Smart Charger 12/50 (1+1) IP43 from VICTRON is ideal thanks to the VE.Direct port for a wired data connection with a color control panel, a PC or other devices. Also note the VictronConnect app for Android and iOS, which you can use with any smartphone or tablet to be wireless and read out your Phoenix Charger via Bluetooth. The programmable relay can also be programmed via the VE.Direct interface or a Bluetooth-compatible device in order to trigger an alarm or other events. Required accessoriesPlease note that an AC connection cable is required for the connection of the Phoenix Smart Charger 12/50 (1+1) IP43 to the power grid. This is not included. scope of delivery1x PSC125051095 VICTRON Phoenix Smart Charger 12/50 (1+1) IP43 1x AC cable clamp 1x operating instructions

Loading programs No. 1, 2, 4 and Li (gel, AGM, acid, lifepo4) adjustable to battery type The charging voltage is free of tips and regulated so that an overload of the batteries is excluded. Fully automatic operation: The charger can be constantly connected to the battery and keeps it in full load. In the event of a network failure, the batteries will not be unloaded (separation by security switch). Lithium LIFEPO4-MAINTENANCE, Auto Wake Up, maintenance phase: Regular automatic activation of the battery cell balancing every 10 days to ensure the full load of the battery. Lead battery regeneration with long downtimes twice a week against harmful acidic layers. Parallel and buffer operation: With simultaneous consumption, the battery is charged or fully received. The adaptation of the loading times calculates and monitors the charger automatically. Monitoring-free charge: Multiple protection against overload, overheating, overvoltage, short circuit, polarity, misconduct and battery recharge through electronic stop to the complete separation of charger and battery with built-in safety switch. Connection for battery temperature sensor (accessories temperature sensor 825, item no. 2001): In the case of lead batteries (acidity, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, causes a better in cold Full loading of the weaker battery, in summer temperatures, unnecessary battery absorbing and thus battery stress is avoided. With LIFEPO4 batteries, the battery temperature sensor is required for the function: it serves battery protection at high and especially at low temperatures below 0 ° C. Silent Run function: At the push of a button noise-optimized way of working (night operation). Power supply function: enables consumers to be supplied without a battery (e.g. battery change). Charging cable compensation: Tension losses on the charging cables are automatically excavated. Construction network filter: Problem-free parallel operation with solar systems, wind and benzingen generators, alternators etc. on a battery. Charging aid for low -level lead batteries: gentle invitation to the (lead -acid, -gel, -gm) battery up to 8 V, then powerful support of the battery with any still switched on consumers. Separation of the batteries in the event of a power failure, overheating, misconduct (safety switch per charging output) Separate side charging output "S" for the support and maintenance charge of the vehicle starter battery Also available in boats with the electronics protected from moisture!   Technical specifications  Network voltage (network frequency 45 - 65 Hz) 110 V - 230 V  Network function voltage area, all types 85 V - 270 V, briefly 305 V (5 seconds)  Network voltage area for full charging power 180 V - 270 V  Network performance max. 490 W  Network performance recording at loading management 1.9 W  Active sinus-shaped power factor correction (Cosphi <= 1) Yes  Charging current approx. 110 V network voltage 18 A  Main charging output battery I  Battery native voltage lead/lifepo4 battery 12 V / 12 V-13.3 V  Selectable charging programs lead gel/AGM/acidity, lifepo4 4  Battery capacity (recommended) 120 Ah - 230 Ah  Battery capacity (after application, e.g. Lifepo4) 75 Ah - 350 Ah  Charging current main load, i-phase, 8 V to U1; 0-15.5 h 30 a  Loading/buffer/load current, regulated U1-U2-U3 phase 0 a - 30 a  Minimum battery voltage for the start of the load 0 V  Preliminary flow, lowest -download batteries 0 V - 8 V 15.0 a  Return current made of battery (power failure) <0.5 MA  Reset voltage (30 sec), battery type dependent 12.75 V / 13.25 V  Charging stress limit (protection of affiliated consumers) 15.0 V  External overvoltage shutdown (20 sec) 15.5 V  Tension <30 MV RMS  Charging timer 4-fold  Group/short circuit/back load/safety protection Yes  Safety timer per loading phase I-/U1-/U2- Yes  Lead battery regeneration with a long service life, 2x aw. 1 H Yes  Lifepo4 car Wake Up at a long time, 10 daily 0.5 h daily Yes  or Lifepo4 lithium rest conservation (seasonal company) Yes  Input for battery temperature sensor Yes  Power supply operation (e.g. further supply for battery changes) Yes  2. Sideline Vehicle Starter Battery II (registration output network)  Battery native voltage (lead) 12 V  Charging current or resilience as a registration output 0 a - 2 a  Group/short circuit/back load/safety protection Yes  Connection for remote control automatic charger Yes  Device installation position any  Temperature range -20 / +45 ° C  Speed ​​-controlled, temperature -controlled fan Yes  Gradual delegation of the charging capacity at over temperature Yes  Safety shutdown at overheating Yes  Fan noise lowering, night operation (Silent Run) Yes  Protection class / protection class I / IP21  Dimensions, Dimensions including fastening flanges/feet, without connections 228 x 139 x 74 mm  Weight 1350 g  Ambient conditions, humidity Max. 95 % RF, not condensing  Safety regulations EN 60335-2-29  Scope of delivery: network cable, operating instructions

The Automatic Charger PB 1215 SMT 2B from Votronic (MPN 3100) is a modern battery charger for mobile use. It has charging programs for gel, AGM, acidity and modern lithium batteries and is designed for 12V battery voltage. The charging current at the main exit is 15a. In addition, there is a side charging output for the starter battery, which can also deliver 2A charging current. The device is suitable for batteries with a capacity from 38AH to 170AH. Important features of the PB 1215 SMT 2B battery loader Reliably charges gel, AGM, acid and Lifepo4 battery 15a charging current, 2A charging current at the side charging output Officelle votronic part number: 3100 Load options: 1 supply and 1 starter battery The charging voltage is free of tips and regulated so that an overload of the batteries is excluded. Fully automatic operation: The charger can be constantly connected to the battery and keeps it in full load. In the event of a network failure, the batteries will not be unloaded (separation by security switch). Lithium LIFEPO4-MAINTENANCE, Auto Wake Up, maintenance phase: Regular automatic activation of the battery cell balancing every 10 days to ensure the full load of the battery. Lead battery regeneration with long downtimes twice a week against harmful acidic layers. Parallel and buffer operation: With simultaneous consumption, the battery is charged or fully received. The adaptation of the loading times calculates and monitors the charger automatically. Monitoring-free charge: Multiple protection against overload, overheating, overvoltage, short circuit, polarity, misconduct and battery recharge through electronic stop to the complete separation of charger and battery with built-in safety switch. Connection for battery temperature sensor (accessories temperature sensor 825, item no. 2001): In the case of lead batteries (acidity, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, causes a better in cold Full loading of the weaker battery, in summer temperatures, unnecessary battery absorbing and thus battery stress is avoided. With LIFEPO4 batteries, the battery temperature sensor is required for the function: it serves battery protection at high and especially at low temperatures below 0 ° C. Silent Run function: At the push of a button noise-optimized way of working (night operation). Power supply function: enables consumers to be supplied without a battery (e.g. battery change). Charging cable compensation: Tension losses on the charging cables are automatically excavated. Construction network filter: Problem-free parallel operation with solar systems, wind and benzingen generators, alternators etc. on a battery. Charging aid for low -level lead batteries: gentle invitation to the (lead -acid, -gel, -gm) battery up to 8 V, then powerful support of the battery with any still switched on consumers. Separation of the B -batteries in the event of a power failure, overheating, misconduct (safety switch per charging output). Separate side charging output "S" for the support and maintenance charge of the vehicle starter battery. Overview of the loading programs of PB 1215 SMT 2B "Gel": charging program for gel batteries, characteristic Iu1ou2ou3 tailored to closed, gas-density gel/dryfit batteries with a defined electrolyte, which generally need a higher loading level and longer U1 holding times to achieve short loading times with particularly high capacity storage and one to avoid long-term battery "starvation". "AGM": charging program for AGM/fleece batteries, characteristic Iu1ou2ou3 intended for loading closed, gas-density AGM (absorbent glass-mat) batteries in lead-fleece technology, which is a particularly high U1 level with coordinated holding times need for full charging and then a moderate U2 level to keep charging (plate and round cells technology). "Universal": charging program for lead-acid/wet/AGM batteries, characteristic line iu1ou2ou3 universal program for loading and loading acid batteries in vehicles (mixed mobile/stationary). And good acid mixture for open and closed, low-maintenance, maintenance-free standard, drive, lighting, solar and heavy duty batteries, as well as AGM batteries with a normal U1 level. "LIFEPO4": charging program for lithium batteries, characteristic Iu1ou2ou3 charging program matched to lithium-lifepo4 batteries with its own BMS and prescribed or built-in protective circuit. Lifetime advantageous charging level of 50-80% and also buffers 12 V consumers and the vehicle starter battery. In addition, a regular Auto Wake Up function activates the batteries cell balancing. Scope of delivery: 1x Votronic 3100 PB 1215 SMT 2B battery charger 1x operating instructions (German)   Technical specifications:  Network voltage (network frequency 45 - 65 Hz) 110 V - 230 V  Network function voltage area, all types 85 V - 270 V, briefly 305 V (5 seconds)  Network voltage area for full charging power 95 V - 270 V  Network performance max. 240 W  Network performance recording at loading management 1.9 W  Active sinus-shaped power factor correction (Cosphi <= 1) Yes  Charging current approx. 110 V network voltage 15 A  Main charging output battery I  Battery native voltage lead/lifepo4 battery 12 V / 12 V-13.3 V  Selectable charging programs lead gel/AGM/acidity, lifepo4 4  Battery capacity (recommended) 60 Ah - 110 Ah  Battery capacity (after application, e.g. Lifepo4) 38 Ah - 170 Ah  Charging current main load, i-phase, 8 V to U1; 0-15.5 h 15 A  Loading/buffer/load current, regulated U1-U2-U3 phase 0 a - 15 a  Minimum battery voltage for the start of the load 0 V  Preliminary flow, lowest -download batteries 0 V - 8 V 7.5 a  Return current made of battery (power failure) <0.5 MA  Reset voltage (30 sec), battery type dependent 12.75 V / 13.25 V  Charging stress limit (protection of affiliated consumers) 15.0 V  External overvoltage shutdown (20 sec) 15.5 V  Tension <30 MV RMS  Charging timer 4-fold  Group/short circuit/back load/safety protection Yes  Safety timer per loading phase I-/U1-/U2- Yes  Lead battery regeneration with a long service life, 2x aw. 1 H Yes  Lifepo4 car Wake Up at a long time, 10 daily 0.5 h daily Yes  or Lifepo4 lithium rest conservation (seasonal company) Yes  Input for battery temperature sensor Yes  Power supply operation (e.g. further supply for battery changes) Yes  2. Sideline Vehicle Starter Battery II (registration output network)  Battery native voltage (lead) 12 V  Charging current or resilience as a registration output 0 a - 2 a  Group/short circuit/back load/safety protection Yes  Connection for remote control automatic charger Yes  Device installation position any  Temperature range -20 / +45 ° C  Speed ​​-controlled, temperature -controlled fan Yes  Gradual delegation of the charging capacity at over temperature Yes  Safety shutdown at overheating Yes  Fan noise lowering, night operation (Silent Run) Yes  Protection class / protection class I / IP21  Dimensions, Dimensions including fastening flanges/feet, without connections 228 x 139 x 74 mm  Weight 1250 g  Ambient conditions, humidity Max. 95 % RF, not condensing  Safety regulations EN 60335-2-29  Scope of delivery: network cable, operating instructions

The Phoenix Smart Charger 12/50 (1+1) IP43 from Victron Energy (MPN PSC125051085) is a powerful battery charger of the latest generation. The device is designed for 12V battery voltage and, in addition to the strong 50a main charging output, also offers a secondary charging output with 3a charging power for a starter battery. The Phoenix Smart Charger 12/50 (1+1) IP43 fits into the integrated Bluetooth module in which the Victron smart family is becoming increasingly becoming, which can be perfectly networked and can also be controlled centrally. In addition to the Bluetooth module, there is also a VE.Direct connection and a freely programmable relay. Optionally, the Smart Battery Sense to control the battery temperature compensation can also be connected. The proven five-stage loading algorithm and the possibility of programming its own charging algorithm make the Phoenix Smart Charger 12/50 (1+1) IP43 a universally applicable high-tec battery cador, which can optimally load almost every battery type. Perfect battery charger for boats and vehicles Phoenix smart battery charger devices that (1+1) contain in the model name have a main charging output, with a full charging current and a 3A ancillary charging output for charging starter batteries. These models are therefore particularly suitable for the mobile area. The Phoenix Smart models with (3) in the model designation were particularly developed with regard to the needs in the marine area and offer three full power outputs for charging 3 battery benches. Highlights of the Phoenix Smart Charger 12/50 (1+1) IP43 Integrated Bluetooth module Integrated VE.Direct connections 1x 50a main charging output and 1 further side charging output for starter batteries Automatic voltage compensation adaptive, five -stage loading algorithm Variable constant stress phase Eye all common types of battery Prevention of damage caused by gastroplating thanks Reduced aging through storage with storage mode Lifepo4 also charges and can be connected to a BMS via optocoupler Fully programmable loading algorithm Remote on/off can be used as a power source Technical features of the Phoenix Smart 12/30 (1+1) Victron part number: PSC125051085 Number of batteries: 1 + 1 (1 main output with full power + 1x starter battery (max. 3a load) Maximum nominal charging current: 50A, battery voltage: 12V High efficiency: 94% Protection class: IP43 (electronic components), IP22 (connection area) You can find more data with the technical data Three integrated technologies for all -round healthy batteries Variable constant voltage phase: always delivers the correct load of charges With a low battery discharge (e.g. a yacht connected to the country current), a short constant voltage phase is chosen to avoid an overload. After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged. Prevention of damage caused by excessive gastung: Batterysafe mode In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage. However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage climb after the gas voltage has been reached (see also the graphics in the brochure). Less maintenance and aging in the resting state of the battery: the storage mode The warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Also perfect for Lifepo4 battery The Phoenix Smart Charger 12/50 (1+1) IP43 can be attached to/off control by connecting a relay or an optocoupler output with an open collector by an Li-Ion BMS to a remote-controlled one/output port . Alternatively, voltage and electricity can also be ruled completely via Bluetooth. Ve.direct interface, bluetooth and programmable relay The Phoenix Smart Charger 12/50 (1+1) IP43 from VICTRON is ideal thanks to the VE.Direct port for a wired data connection with a color control panel, a PC or other devices. Also note the VictronConnect app for Android and iOS, which you can use with any smartphone or tablet to be wireless and read out your Phoenix Charger via Bluetooth. Programmable relay can also be programmed via the VE.Direct interface or a Bluetooth-compatible device in order to trigger an alarm or other events. Required accessories Please note that an AC connection cable is required for the connection of the Phoenix Smart Charger 12/50 (1+1) IP43 to the power grid. This is not included. You can find the right connection cable here: Frenchman Energy Frenchman marine   scope of delivery 1x PSC125051085 VICTRON Phoenix Smart Charger 12/50 (1+1) IP43 1x AC cable clamp 1x operating instructions   data sheet IP protection IP43 Communication sports Bluetooth, ve.direct EAN 8719076041627 Manufacturer part number PSC125051085 Ambient temperature -20 ° C - +60 ° C Battery voltage 12V Number of charging outputs 1 + 1 Battery type adjustable Acid, gel, AGM, LIFEPO4 Charging Adaptive battery management Protective functions Polation on the battery, output ceiling, over temperature guarantee 2 years Temperature compensation Yes, via Smart Battery Sense humidity Max. 95 %, not condensing Manufacturer Victron Energy Weight 3.6 kg Dimensions (LXBXH) 24.9 x 18 x 10 cm

The Phoenix Smart Charger 12/50 (3) IP43 by Victron Energy (MPN PSC125053085) is a powerful battery charger of the latest generation. The device is designed for 12V battery voltage and offers 3 charging outputs, each of which is able to deliver full charging current. The Phoenix Smart Charger 12/50 (3) IP43 fits into the integrated Bluetooth module in which the Victron smart family is becoming increasingly becoming, which can be perfectly networked and can also be controlled centrally. In addition to the Bluetooth module, there is also a VE.Direct connection and a freely programmable relay. Optionally, the Smart Battery Sense to control the battery temperature compensation can also be connected. The proven five-stage loading algorithm and the possibility of programming its own charging algorithm make the Phoenix Smart Charger 12/50 (3) IP43 a universally applicable high-tec battery loader, which can optimally load almost every battery type. Perfect battery charger for boats and vehicles Phoenix smart battery charger devices that (1+1) contain in the model name have a main charging output, with a full charging current and a 3A ancillary charging output for charging starter batteries. These models are therefore particularly suitable for the mobile area. The Phoenix Smart models with (3) in the model designation were particularly developed with regard to the needs in the marine area and offer three full power outputs for charging 3 battery benches. Highlights of the Phoenix Smart Charger 12/50 (3) IP43 Integrated Bluetooth module Integrated VE.Direct connections 3x 50a charging outputs are available (maximum 50a charging current) Automatic voltage compensation adaptive, five -stage loading algorithm Variable constant stress phase Eye all common types of battery Prevention of damage caused by gastroplating thanks Reduced aging through storage with storage mode Lifepo4 also charges and can be connected to a BMS via optocoupler Fully programmable loading algorithm Remote on/off can be used as a power source Technical features of the Phoenix Smart 12/30 (1+1) Victron part number: PSC125053085 Number of batteries: 3 (each output can output the full charging capacity of the device) Maximum nominal charging current: 50A, battery voltage: 12V High efficiency: 94% Protection class: IP43 (electronic components), IP22 (connection area) You can find more data with the technical data Three integrated technologies for all -round healthy batteries Variable constant voltage phase: always delivers the correct load of charges With a low battery discharge (e.g. a yacht connected to the country current), a short constant voltage phase is chosen to avoid an overload. After a deep discharge, the constant voltage phase is automatically extended to ensure that the battery is fully charged. Prevention of damage caused by excessive gastung: Batterysafe mode In order to shorten the loading time, the highest possible charging current was selected together with a high constant voltage. However, in order for an excessive gas development to be avoided towards the end of the constant trump phase, the charger limits the speed of the voltage climb after the gas voltage has been reached (see also the graphics in the brochure). Less maintenance and aging in the resting state of the battery: the storage mode The warehouse mode is always activated if no discharge has been carried out within 24 hours. In storage mode, the loading tension is then reduced to 2.2 V/cell (13.2 V for a 24 V battery) in order to minimize gas development and corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure. Also perfect for Lifepo4 battery The Phoenix Smart Charger 12/50 (3) IP43 can be attached to/off control by connecting a relay or an optocoupler output with an open collector by a Li-ion BMS to a remote-controlled one/output port. Alternatively, voltage and electricity can also be ruled completely via Bluetooth. Ve.direct interface, bluetooth and programmable relay The Phoenix Smart Charger 12/50 (3) IP43 from VICTRON is ideally suited for a wired data connection with a color control panel, a PC or other devices. Also note the VictronConnect app for Android and iOS, which you can use with any smartphone or tablet to be wireless and read out your Phoenix Charger via Bluetooth. Programmable relay can also be programmed via the VE.Direct interface or a Bluetooth-compatible device in order to trigger an alarm or other events. Required accessories Please note that an AC connection cable is required for the hint of the Phoenix Smart Charger 12/50 (3) IP43 to the power grid. This is not included. You can find the right connection cable here: Frenchman Energy Frenchman marine   scope of delivery 1x PSC125053085 VICTRON Phoenix Smart Charger 12/50 (3) IP43 1x AC cable clamp 1x operating instructions   data sheet IP protection IP43 Communication sports Bluetooth, ve.direct EAN 8719076041634 Manufacturer part number PSC125053085 Ambient temperature -20 ° C - +60 ° C Battery voltage 12V Number of charging outputs 3 Battery type adjustable Acid, gel, AGM, LIFEPO4 Charging Adaptive battery management Protective functions Polation on the battery, output ceiling, over temperature guarantee 2 years Temperature compensation Yes, via Smart Battery Sense humidity Max. 95 %, not condensing Manufacturer Victron Energy Weight 3.6 kg Dimensions (LXBXH) 24.9 x 18 x 10 cm

The Blue Smart IP22 12/20 (3) charger of Victron Energy (MPN BPC12204002), is a professional, compact 12V 20A battery charger of the latest generation with 3 charging outputs and built -in Bluetooth! The Blue Smart IP22 12/20 (3) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 12V lead batteries and modern lithium batteries. It offers Highlights of the 12/20 (3) Blue Smart IP22 Charger Intelligent charging until the perfect battery state ... The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life. Restoration of deep-downloaded "dead" batteries Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections. Call the battery status from afar, with the VictronConnect app The Blue Smart IP22 12/20 (3) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. The most important technical features of the 12/20 (3) Blue Smart IP22 Charger Victron part number: BPC122044002 Lades 12V lead-acid, gel, agm and lithium batteries 20a maximum charging current 3 battery charging outputs Very compact dimensions: 235 x 108 x 65mm Highly modern, seven-level loading algorithm With integrated Bluetooth for use with the free VictronConnect app Other features of the 12/20 (3) Blue Smart IP22 Batterieladers Trend -setting efficiency With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard. Adaptive 7-stable loading algorithm The 12/20 (3) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. "Adaptive" means that the loading process is automatically adjusted to the type of battery use. Storage mode: Less maintenance and aging in the resting state of the battery The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 12V battery) in order to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure.   Scope of delivery: 1x Victron Energy BPC122044002 12/20 (3) IP22 Blue Smart Charger 1x operating instructions IP protection IP22 EAN 8719076037446 Ambient temperature -20 ° C - +50 ° C Manufacturer part number BPC122044002 guarantee 2 years humidity Max. 98 %, not condensing Manufacturer Victron, Victron Energy Weight 1.3 kg Dimensions (LXBXH) 10.8 x 23.5 x 6.5 cm  

  Loading programs No. 1, 2, 4 and Li (gel, AGM, acid, lifepo4) adjustable to battery type The charging voltage is free of tips and regulated so that an overload of the batteries is excluded. Fully automatic operation: The charger can be constantly connected to the battery and keeps it in full load. In the event of a network failure, the batteries will not be unloaded (separation by security switch). Lithium LIFEPO4-MAINTENANCE, Auto Wake Up, maintenance phase: Regular automatic activation of the battery cell balancing every 10 days to ensure the full load of the battery. Lead battery regeneration with long downtimes twice a week against harmful acidic layers. Parallel and buffer operation: With simultaneous consumption, the battery is charged or fully received. The adaptation of the loading times calculates and monitors the charger automatically. Monitoring-free charge: Multiple protection against overload, overheating, overvoltage, short circuit, polarity, misconduct and battery recharge through electronic stop to the complete separation of charger and battery with built-in safety switch. Connection for battery temperature sensor (accessories temperature sensor 825, item no. 2001): In the case of lead batteries (acidity, gel, AGM), the charging voltage is automatically adjusted to the battery temperature, causes a better in cold Full loading of the weaker battery, in summer temperatures, unnecessary battery absorbing and thus battery stress is avoided. With LIFEPO4 batteries, the battery temperature sensor is required for the function: it serves battery protection at high and especially at low temperatures below 0 ° C. Silent Run function: At the push of a button noise-optimized way of working (night operation). Power supply function: enables consumers to be supplied without a battery (e.g. battery change). Charging cable compensation: Tension losses on the charging cables are automatically excavated. Construction network filter: Problem-free parallel operation with solar systems, wind and benzingen generators, alternators etc. on a battery. Charging aid for low -level lead batteries: gentle invitation to the (lead -acid, -gel, -gm) battery up to 8 V, then powerful support of the battery with any still switched on consumers. Separation of the batteries in the event of a power failure, overheating, misconduct (safety switch per charging output) Separate side charging output "S" for the support and maintenance charge of the vehicle starter battery Also available in boats with the electronics protected from moisture!   Technical specifications  Network voltage (network frequency 45 - 65 Hz) 110 V - 230 V  Network function voltage area, all types 85 V - 270 V, briefly 305 V (5 seconds)  Network voltage area for full charging power 180 V - 270 V  Network performance max. 400 W  Network performance recording at loading management 1.9 W  Active sinus-shaped power factor correction (Cosphi <= 1) Yes  Charging current approx. 110 V network voltage 18 A  Main charging output battery I  Battery native voltage lead/lifepo4 battery 12 V / 12 V-13.3 V  Selectable charging programs lead gel/AGM/acidity, lifepo4 4  Battery capacity (recommended) 100 Ah - 180 Ah  Battery capacity (after application, e.g. Lifepo4) 60 Ah - 290 Ah  Charging current main load, i-phase, 8 V to U1; 0-15.5 h 25 a  Loading/buffer/load current, regulated U1-U2-U3 phase 0 a - 25 a  Minimum battery voltage for the start of the load 0 V  Preliminary flow, lowest -download batteries 0 V - 8 V 12.5 a  Return current made of battery (power failure) <0.5 MA  Reset voltage (30 sec), battery type dependent 12.75 V / 13.25 V  Charging stress limit (protection of affiliated consumers) 15.0 V  External overvoltage shutdown (20 sec) 15.5 V  Tension <30 MV RMS  Charging timer 4-fold  Group/short circuit/back load/safety protection Yes  Safety timer per loading phase I-/U1-/U2- Yes  Lead battery regeneration with a long service life, 2x aw. 1 H Yes  Lifepo4 car Wake Up at a long time, 10 daily 0.5 h daily Yes  or Lifepo4 lithium rest conservation (seasonal company) Yes  Input for battery temperature sensor Yes  Power supply operation (e.g. further supply for battery changes) Yes  2. Sideline Vehicle Starter Battery II (registration output network)  Battery native voltage (lead) 12 V  Charging current or resilience as a registration output 0 a - 2 a  Group/short circuit/back load/safety protection Yes  Connection for remote control automatic charger Yes  Device installation position any  Temperature range -20 / +45 ° C  Speed ​​-controlled, temperature -controlled fan Yes  Gradual delegation of the charging capacity at over temperature Yes  Safety shutdown at overheating Yes  Fan noise lowering, night operation (Silent Run) Yes  Protection class / protection class I / IP21  Dimensions, Dimensions including fastening flanges/feet, without connections 228 x 139 x 74 mm  Weight 1300 g  Ambient conditions, humidity Max. 95 % RF, not condensing  Safety regulations EN 60335-2-29  Scope of delivery: network cable, operating instructions