Device Combinations

Der Multiplus-II 48/5000/70-50 von Victron Energy ist eine High-End Gerätekombination, welche die klassische Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Islanding Funktion verbindet. Dadurch werden die Funktionen PowerControl und PowerAssist auf 100 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 5000 W, bzw. 4000 W bei linearer Dauerbelastung. Auch das 48 V Batterieladegerät ist mit 70 A Ladeleistung sehr gut proportioniert und wird durch einen 50 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. wichtige Leistungsmerkmale- PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung- eingebaute Anti-Islanding-Funktion und Anschlussmöglichkeit für externen Stromsensor (optional)- kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen- einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen- bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen- VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration- praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb- kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werdentechnische Merkmale- 5000 W Leistung bei nicht linearer Belastung 4000 W Dauerbelastung und 9000 W Spitzenleistung- für 48 V Batteriespannung, 50 A Transfer-Schalter und 70 A Batterieladegerät- Ausgangsspannung: 230 VAC, Frequenz: 50 Hz- max. Wirkungsgrad liegt bei 95%, Schutzklasse IP22immer genug Power dank PowerControl und PowerAssistAm Multiplus-II 48/5000/70-50 kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Das MultiPlus-II nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Solarstrom: Wechselstrom auch bei NetzausfallDas Gerät kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es lässt sich sowohl mit Solar-Lade-Reglern als auch mit netzgebundenen Wechselrichtern verwenden. maximale Flexibilität dank zweier WechselstromausgängeDer Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt das MultiPlus-II die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. viele Möglichkeiten zur SystemerweiterungDie Einstellungen lassen sich mit der VEConfigure Software binnen weniger Minuten ändern (es ist dafür ein Computer oder Laptop und ein MK3-USB-Interface notwendig).Es stehen mehrere Überwachungs- und Steuerungs-Optionen zur Verfügung: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (mit dem optionalen VE.Bus Smart Dongle), Batterie-Wächter, Digital Multi Bedien-Paneel. Konfiguration und Überwachung aus der FerneInstallieren Sie ein Color Control GX oder andere GX-Produkte, um sich mit dem Internet zu verbinden. Die Betriebs Daten lassen sich auf unserer VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Sind Systeme an das Internet angeschlossen, kann auf sie aus der Ferne zugegriffen und Einstellungen können geändert werden.

Der Multiplus-II 48/3000/35-32 ist eine High-End Gerätekombination von Victron Energy die klassische Multiplus-Komponenten mit einem externen Stromsensor und integrierter Anti-Islanding Funktion verbindet. Dadurch werden die Funktionen PowerControl und PowerAssist auf 50 A erweitert und der potenzielle Einsatzbereich auf ESS-Anwendungen ausgedehnt. Das Wechselrichter Modul leistet bei nicht linearer Belastung satte 3000 W, bzw. 2400 W bei linearer Dauerbelastung. Auch das 48 V Batterieladegerät ist mit 35 A Ladeleistung sehr gut proportioniert und wird durch einen 32 A Transferschalter ergänzt, mit dem sich blitzschnell zwischen den AC-Anschlüssen hin- und herschalten lässt. wichtige Leistungsmerkmale- PowerControl und PowerAssist –Steigerung von Netz-oder Generator-Leistung- eingebaute Anti-Islanding-Funktion und Anschlussmöglichkeit für externen Stromsensor (optional)- kann als Backupgerät in netzgekoppelten Anlagen eingesetzt für die Stromversorgung bei Netzausfällen- einsetzbar in verschiedenen ESS (Energy Storage System) Anwendungen- bestens geeignet für die professionelle Seefahrt, Yachten, Fahrzeuge und landgebundene, netzferne Anwendungen- VE.Bus Schnittstelle für Parallel-und Drei-Phasen-Betrieb, Fernüberwachung und Systemintegration- praktisch unbegrenzte Leistung durch Parallel-und Drei-Phasen-Betrieb- kann vor Ort oder aus der Ferne mittels VEConfigure Software konfiguriert werdentechnische Merkmale- 3000W Leistung bei nicht linearer Belastung 2400 W Dauerbelastung und 6000 W Spitzenleistung- für 48 V Batteriespannung, 32 A Transfer-Schalter und 35 A Batterieladegerät- Ausgangsspannung: 230 VAC, Frequenz: 50 Hz- max. Wirkungsgrad liegt bei 95%, Schutzklasse IP22- immer genug Power dank PowerControl und PowerAssist Am Multiplus-II 48/3000/35-32 kann ein maximaler Netz- oder Generatorstrom eingestellt werden. Das MultiPlus-II nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden der Batterie nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Netzanschluss überlastet wird (PowerControl-Funktion). Mit der Funktion PowerAssist erhält das PowerControl-Prinzip eine neue Dimension. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall kompensiert das MultiPlus-II zu schwache Generator-, Landstrom- bzw. Netzleistung sofort durch Energie aus der Batterie. Wird die Last reduziert, d. h. werden Verbraucher ausgeschaltet, kann die dann wieder ausreichend vorhandene Energie zum Laden der Batterien genutzt werden. Solarstrom: Wechselstrom auch bei NetzausfallDas Gerät kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es lässt sich sowohl mit Solar-Lade-Reglern als auch mit netzgebundenen Wechselrichtern verwenden. maximale Flexibilität dank zweier WechselstromausgängeDer Hauptausgang stellt einen unterbrechungsfreien Betrieb sicher. Im Falle eines Netzausfalls oder bei einer Unterbrechung des Land-/Generatorstroms übernimmt das MultiPlus-II die Versorgung der angeschlossenen Verbraucher. Die Umschaltung geschieht so schnell (in weniger als 20 Millisekunden), dass ein unterbrechungsfreier Betrieb von Computern und anderen elektronischen Geräten gewährleistet ist. Der zweite Ausgang liefert nur dann Strom, wenn am Eingang des MultiPlus-II Wechselstrom verfügbar ist. Verbraucher, die die Batterie nicht entladen dürfen, wie z. B. ein Wassererhitzer, können an diesen Ausgang angeschlossen werden. viele Möglichkeiten zur SystemerweiterungDie Einstellungen lassen sich mit der VEConfigure Software binnen weniger Minuten ändern (es ist dafür ein Computer oder Laptop und ein MK3-USB-Interface notwendig).Es stehen mehrere Überwachungs- und Steuerungs-Optionen zur Verfügung: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (mit dem optionalen VE.Bus Smart Dongle), Batterie-Wächter, Digital Multi Bedien-Paneel. Konfiguration und Überwachung aus der FerneInstallieren Sie ein Color Control GX oder andere GX-Produkte, um sich mit dem Internet zu verbinden. Die Betriebs-Daten lassen sich auf unserer VRM (Victron Remote Management) Website kostenlos speichern und einsehen. Sind Systeme an das Internet angeschlossen, kann auf sie aus der Ferne zugegriffen und Einstellungen können geändert werden.

TheMultiplus-II 48/3000/35-32 GX from Victron Energy Is a high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 50 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 3000 W or 2400 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, with which it can be switched back and forth between the AC connections. Compared to the remaining devices of the series, the GX variants have an integrated GX display with numerous other connection options. Important performance features- Integrated GX control device with various communication connections-PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- can be used as a backup device in network -coupled systems for the power supply for network failures- Can be used in various ESS (Energy Storage System) Applications- Ideally suited for professional seafaring, yachts, vehicles and land -related, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation.- Can be configured on site or from a distance using Veconfigure software*technical features- 3000W power with non -linear load 2400 W continuous load and 6000 W Top output- for 48 V battery voltage, 32 A transfer switch and 35 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- Max. Efficiency is 95%, protection class IP22- Always enough power thanks to PowerControl and Power Assist A maximum network or generator current can be set on the Multiplus-II 48/3000/35-32 GX. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. If the load is reduced, i.e. consumers are switched off, the energy that is sufficiently existing can then be used again for charging the batteries. Solar power: Alternating current even in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Scope of the integrated GX deviceA VE.CAN interface can be used to connect Victron (e.g. Ve.CAN MPPT) Ve.CAN devices. The connection can also be configured via the remote console for use with a compatible CAN bus Li-ion battery.1xusb connection, 1x Ethernet connection, 1x VE.Direct connection offer many options for system extensionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary).Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel . Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

The Multiplus-II 12/3000/120-32 is a high-end device combination of Victron Energy that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. This expands the functions PowerControl and Power Assist to 50 A. The inverter module provides a whopping 3000 W or 2400 W with a linear permanent burden on non -linear loads. The 12 V battery charger is also very well proportioned with 120 A charging power and is supplemented by a 32 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features of the Multiplus-II 12/3000/120-32PowerControl and Power Assist increase in network or generator performanceBuilt-in anti-Icelanding function and connection option for external electricity sensor (optional)Can be used as a backup device in network -coupled systems for the power supply for network failurescan be used in different applicationsIdeally suited for professional seafaring, yachts, vehicles and land -bound, native applicationsVe.Bus interface for parallel and three-phase operation, remote monitoring and system integrationPractically unlimited performance through parallel and three-phase operationCan be configured on site or from a distance using Veconfigure softwaretechnical features3000 W power with non -linear load 2400 W continuous load and 5500 W Top performancefor 12 V battery voltage, 32 A transfer switch and 120 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. Effect is 95%, protection class IP22Always enough power thanks to PowerControl and Power Assist A maximum network or generator current can be set on the Multiplus-II 12/3000/120-32. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to charge the batteries. Solar power: alternating current also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Many options for system expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

TheMultiplus-II 48/5000/70-50 GX from Victron Energy is a high-end device combination that combines the classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 100 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 5000 W or 4000 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, with which it can be switched back and forth between the AC connections.Compared to the remaining devices of the series, the GX variants have an integrated GX display with numerous other connection options. Important performance features- Integrated GX control device with various communication connections- PowerControl and Power Assist increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- can be used as a backup device in network -coupled systems for the power supply for network failures- Can be used in various ESS (Energy Storage System) Applications- Ideally suited for professional seafaring, yachts, vehicles and land -related, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure softwaretechnical features- 5000 W power with non -linear load 4000 W continuous load and 9000 W peak output- for 48 V battery voltage, 50 A transfer switch and 70 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- Max. Efficiency is 95%, protection class IP22Always enough power thanks to PowerControl and Power AssistA maximum network or generator current can be set on the Multiplus-II 48/5000/70-50 GX. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to charge the batteries. Solar power: A changeover also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Scope of the integrated GX device A VE.CAN interface This can be used to connect Victron (e.g. Ve.CAN MPPT) Ve.CAN devices. The connection can also be configured via the remote console for use with a compatible CAN bus Li-ion battery.1xusb connection1x Ethernet connection1x Ve.direct connectionmany options for system expansion The settings can be used with the VEconfigure software Binside WChange the extent (a computer or laptop and an MK3 USB interface). Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital Multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The company data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

TheMultiplus-II 24/3000/70-32 from Victron Energy is a high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 50 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 3000 W or 2400 W with a linear permanent burden on non -linear loads. The 24 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 32 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features -PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- can be used as a backup device in mesh -coupled systems for the power supply for network failures- Can be used in various ESS (Energy Storage System) Applications- Ideally suited for professional seafaring, yachts, vehicles and land -related, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure softwaretechnical features- 3000 W power with non -linear load 2400 W continuous load and 6000 W Top output- for 24 V battery voltage, 32 A transfer switch and 70 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- Max. Efficiency is 95%, protection class IP22- PowerControl and power assist A maximum network or generator current can be set on the Multiplus-II 24/3,000/70-32. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to charge the batteries. Solar power: A changeover also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. many options for system expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

TheMultiplus-II 24/5000/120-50 is a high-end device combination of Victron Energy, which combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 100 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 5000 W or 4000 W with a linear permanent burden on non -linear loads. The 24 V battery charger is also very well proportioned with 120 A charging power and is supplemented by a 50 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features- PowerControl and Power Assist increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- can be used as a backup device in network -coupled systems, for the power supply for network failuresCan be used in various ESS (Energy Storage System) applications- Ideally suited for professional seafaring, yachts, vehicles and land -related, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure softwaretechnical features- 5000 W power with non -linear load 4000 W continuous load and 9000 W Top output- for 24 V battery voltage, 50 A transfer switch and 120 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- Max. Efficiency is 95%, protection class IP22- Note: Not standardized according to EN 50-549PowerControl and Power AssistA maximum network or generator current can be set on the Multiplus-II 24/5000/120-50. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. The load is reduced, i.e. H. If consumers are switched off, the energy that is then sufficiently existing can be used again to charge the batteries.Solar power: Alternating current even in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Many options for System expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

Hybrid-Wechselrichter/LadegerätDer Multi RS Solar 48/6000 ist ein Wechselrichter/Ladegerät für 48 V & 6 kVA mit 450 VDC 4 kWp PV-Eingang. Kombination aus Wechselrichter, Wechselstromladegerät und Solar MPPTDer Wechselrichter erzeugt eine perfekte Sinuswelle, die in der Lage ist, Geräte mit hoher Leistung zu versorgen. Er funktioniert außerdem beidseitig, d. h. er lädt bei überschüssigem Solarstrom oder Wechselstrom die Batterie auf oder wandelt diesen bei Bedarf um. Großer MPPT-Spannungsbereich80 - 450 VDC, mit einer PV-Einschaltspannung von 120 VDC. Leicht, effizient und leiseDank der Hochfrequenztechnik und eines neuen Designs wiegt dieser leistungsstarke Wechselrichter nur 11 kg. Darüber hinaus hat es einen ausgezeichneten Wirkungsgrad, eine geringe Standby-Leistung und einen sehr leisen Betrieb. Display, Bluetooth und VictronConnect AppDas Display liest die Batterie-, Wechselrichter- und Solarparameter ab. Auf die gleichen Parameter kann mit einem Smartphone oder einem anderen Bluetooth-fähigen Gerät über die VictronConnect-App zugegriffen werden. Erweiterbare PV-Kapazität, sowohl mit Wechselstrom als auch mit Gleichstrom gekoppeltDie integrierte PV-Kapazität von 4 kWp kann durch Hinzufügen von Solarladegeräten zum System erweitert werden, zum Beispiel durch unsere Smart Solarladegeräte, einschließlich der Smart Solar RS-Modelle. Bei Anschluss an ein VE.Can-Netz werden alle Batterieladungen simultan und in koordinierter Weise durchgeführt.Alternativ kann die PV-Kapazität durch die Installation von PV-Wechselrichtern erweitert werden, deren Ausgangsleistung automatisch durch die integrierte Frequenzverschiebungssteuerung gesteuert wird. SchnittstellenVe.Can-Anschluss an ein GX-Gerät zur Systemüberwachung, Datenprotokollierung und Firmware-Aktualisierung aus der Ferne. VE.Direct-Verbindung zu einem GlobalLink 520 zur Datenfernüberwachung. E/A-VerbindungenProgrammierbare Relais-, Temperatursensor- und Spannungssensoranschlüsse. Der Ferneingang kann auch so konfiguriert werden, dass er das Victron smallBMS akzeptiert.

TheMultiplus-II 48/8000/110-100 from Victron Energy is a high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 100 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 8000 W or 6400 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 110 A charging power and is supplemented by a 100 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features -PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- used as a backup device in network -coupled systems for the power supply for network failuresCan be used in various ESS (Energy Storage System) applications-for professional seafaring, yachts, vehicles and land -bound, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure software*technical features8000 W power with non -linear load 6400 W continuous load and 15000 W peak outputFor 48 V battery voltage, 100 A transfer switch and 110 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. Effect is 95%, protection class IP22Always enough power thanks to PowerControl and Power AssistA maximum network or generator current can be set on the Multiplus-II 48/8000/110-100. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. If the load is reduced, i.e. consumers are switched off, the energy that is sufficiently existing can then be used again for charging the batteries. Solar power: A changeover also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Many options for system expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

Der MultiPlus C 12/1600/70-16 von Victron ist eine leistungsstarke Gerätekombination für dein Energieversorgungssystem. Er vereint einen 12V 1300W Sinus-Wechselrichter und ein effizientes Batterie-Ladegerät. Dieses liefert dir beeindruckende 70A, sodass auch große Batterien schnell geladen werden können, wenn Land- oder Netzstrom verfügbar ist. Der Inverter wandelt den Batteriestrom in 230V Wechselstrom um und bietet damit eine optimale Stromqualität für empfindliche elektronische Geräte. Zusätzlich verfügt der MultiPlus über einen blitzschnellen 16A Transferschalter, der ihn ideal für Wohnmobile, Boote, Yachten und netzgekoppelte USV-Anlagen macht. In Eigenverbrauchsanlagen sorgt er dafür, dass nur dann Strom aus dem Netz bezogen wird, wenn der Batteriestrom nicht ausreicht. Bei einem Netzausfall gewährleistet er eine unterbrechungsfreie Stromversorgung. Highlights des MultiPlus C 12/1600/70 Gerätekombination aus Wechselrichter mit Transfer-Switch und 70A Batterieladegerät VE.Bus Kommunikationsport für Vernetzung, Systemintegration und Konfigurationen Unterstütz den Drei-Phasen-Betrieb in Parallelschaltung Überwachung vor Ort oder per Fernüberwachung mit der App Zwei Wechselstromausgänge PowerControl-Mechanismus PowerAssist Programmierbares Relais Vielseitig einsetzbar Für netzunabhängige als auch netzgekoppelte PV-Anlagen Massiver Leistungsausbau möglich Neben dem parallelen Anschluss können drei Einheiten desselben Modells auch zu einer leistungsstarken Drei-Phasen-Ausgangskonfiguration kombiniert werden. Doch das ist noch nicht alles - Bis zu sechs Sets mit jeweils drei Einheiten lassen sich parallel schalten, um beeindruckende 75kW / 90kVA Wechselrichterleistung und über 2.000A Ladekapazität zu erreichen. PowerControl Der MultiPlus ist ein äußerst leistungsstarkes Batterieladegerät, das relativ viel Strom vom Generator oder Landstromanschluss benötigt (fast 10A pro 5kVA Multi bei 230V AC). Mit dem Multi Control Fernbedienungspanel kannst du jedoch den maximalen Stromverbrauch einfach einstellen. Er berücksichtigt dabei automatisch die anderen angeschlossenen Geräte und nutzt nur den überschüssigen Strom zum Laden. Dadurch wird sichergestellt, dass der Generator oder der Landstromanschluss niemals überlastet wird. PowerAssist Diese Funktion hebt das PowerControl-Prinzip auf ein neues Niveau. Der MultiPlus kann nun schwache alternative Energiequellen effektiv unterstützen. Da Lastspitzen oft nur kurzzeitig auftreten, sorgt die Gerätekombi dafür, dass eine zu schwache Landstrom- oder Generatorleistung sofort durch Energie aus der Batterie ausgeglichen wird. Sobald die Lasten abnehmen, also wenn Verbraucher abgeschaltet werden, kann die überschüssige Energie wieder effizient zum Laden der Batterien genutzt werden. Systemkonfiguration Einstellungen an einem Einzelgerät kannst du innerhalb weniger Minuten einfach mittels eines DIP-Schalter-Verfahrens vornehmen. Parallele und Drei-Phasen-Systeme lassen sich bequem mit der VE.Bus Quick Configure- und VE.Bus System Configurator-Software konfigurieren. Netzunabhängige, netzgekoppelte und Eigenverbrauchssysteme in denen Grid-Tie-Wechselrichter und/oder MPPT-Solarladegeräte zur Verwendung kommen, können problemlos mit der entsprechenden Assistenten-Software konfiguriert werden.       Überwachung - Wo und Wann immer du willst Dir stehen mehrere Möglichkeiten offen, um deine Daten entweder vor Ort oder per Fernüberwachung im Auge zu behalten und sofort reagieren zu können. Hier ein paar Beispiele für dich: Ekrano GX und Cerbo GX - Bietet eine benutzerfreundliche Systemsteuerung und -überwachung und ermöglicht den Zugriff auf das kostenlose VRM Online Portal zur Einsicht aus der Ferne.
VRM-Portal - Das kostenlose Tool zeigt alle Daten deines Systems in einem übersichtlichen grafischen Format an. Über diese Anwendung kannst du Systemänderungen bequem von überall aus vornehmen. Zudem erhältst du Alarme direkt per E-Mail oder Push-Benachrichtigung.
VRM-App - Du kannst dein Victron Energy System bequem über dein Smartphone oder Tablet überwachen und verwalten. Die App steht sowohl für iOS als auch für Android zur Verfügung. Technische Daten Wechselrichter Eingangsspannungsbereich: 9-17V DC / 19-33V DC / 38-66V DC Ausgangsspannung: 230V AC ± 2% Frequenz: 50Hz ± 1% Kont. Ausgangsleistung bei 25°C: 1600VA (nichtlineare Last) Kont. Ausgangsleistung bei 25°C: 1300W Kont. Ausgangsleistung bei 40°C: 1200W Kont. Ausgangsleistung bei 65°C: 800W Spitzenleistung: 3000W Max. Wirkungsgrad: 93% Ladegerät Eingangsspannungsbereich: 187-265V AC Eingangsfrequenz: 45-65Hz / Leistungsfaktor: 1 Ladespannung-Konstantspannung: 14,4/28,8/57,6V DC Ladespannung-Ladeerhaltung: 13,8/27,6/55,2V DC Lagermodus: 13,2/26,4/52,8V DC Ladestrom Hausbatterie: 70A Ladestrom Starterbatterie: 4A (nur 12V und 24V Modelle) Allgemeines Wechselstromeingang - Eingangsspannungsbereich: 187-250V Wechselstromeingang - Eingangsfrequenz: 50/60Hz Transferschalter: 16A Betriebstemperaturbereich: -40°C - +65°C Feuchtigkeit: max. 95% (nicht kondensierend) Batterieanschluss: 1,5m Batteriekabel 230V AC Anschluss: G-St18i-Anschluss Schutzart: IP20 Gewicht: 10kg Abmessungen: 375 x 214 x 110mm Lieferumfang 1x Victron MultiPlus C 12/1600/70-16 230V VE.Bus Gerätekombination 3000W Wechselrichter 70A Ladegerät

Der Multiplus 12/2000/80-32 von Victron Energy ist eine Gerätekombination aus 12V 2000W Sinus Wechselrichter und Batterie-Ladegerät. Das fest integrierte Batterieladegerät leistet beachtliche 80A womit auch großzügige Batterien schnell voll geladen werden können, wenn Land-/Netzstrom zur Verfügung steht. Der im Multiplus verbaute 12V Sinus Spannungswandler wandelt Ihren Strom aus der Batterie in 230V Wechselstrom um. Dank der echten Sinuswelle ist die Stromqualität auch für empfindliche elektronische Geräte perfekt geeignet. Neben den beiden integrierten Gerätetypen ist auch ein blitzschneller 32A Transferschalter verbaut mit dem sich auch zahlreiche netzgekoppelte Lösungen umsetzen lassen. Zur Systemintegration verfügt der MultiPlus über einen VE.Bus Port was quasi eine grenzenlose Vernetzung ermöglicht. Umfassend und flexibel einsetzbarDa er neben Wechselrichter und Ladegerät auch noch über einen blitzschnellen 32A Transferschalter verfügt, ist er ein idealer Wechselrichter für die Bereiche Wohnmobil, Boot oder Yacht und den netzgekoppelten Bereich der unterbrechungsfreien Stromversorgung im Falle von Netzschwankungen oder Stromausfällen. Auch für den Einsatz in netzgekoppelten Eigenverbrauchsanlagen die nur Strom vom Versorger ziehen wenn der Batteriestrom nicht mehr ausreicht oder als USV Lösung in der die Multiplus einspringen wenn der Strom vom Netzbetreiber plötzlich ausfällt und so für eine unterbrechungsfreie Stromversorgung sorgen. Leistungsmerkmale des Multiplus 12/2000/80-321600W Dauerleistung und 3500W Spitzenleistung, für 12V BatteriespannungGerätekombination aus Wechselrichter mit Transfer-Switch und 80A Batterieladegerätliefert reinste 230V Sinusspannung und eine saubere 50Hz FrequenzVE.Bus Kommunikationsport sorgt für umfangreiche Möglichkeiten der Vernetzung, Systemintegration, Konfiguration und Kontrolle der Multiplus Geräte von Victronunterstützt den Drei-Phasen-Betrieb (3 gleiche Einheiten des selben Models benötigt)Multiplus Geräte sind parallelschaltfähig, bis zu 6 Geräte lassen sich parallel verbinden und die Systemleistung dadurch im Bedarfsfall deutlich steigernPowerControl Funktion ermöglicht das Arbeiten mit begrenzter Generatorleistung so wie eingeschränktem Land- oder NetzstromPowerAssist Funktion ermöglicht “Leistungssteigerung“ von Generatoren und Landanschlussunterstützung im Bedarfsfallals USV Lösung zur unterbrechungsfreien Stromversorgung einsetzbar, dank des integrierten Transferschaltersfür netzgekoppelte Eigenverbrauchsanlagen einsetzbar die nur dann Strom vom Netzbetreiber ziehen wenn die Batteriekapazität nicht mehr ausreicht oder andere programmierbare Ereignisse stattgefunden habenkompatibel mit zahlreichen Victron Steuer- und AnzeigepanelsMassiver Leistungsausbau möglichAbgesehen von dem parallelen Anschluss, können auch drei Einheiten desselben Modells für einen Drei-Phasen-Ausgang konfiguriert werden. Damit jedoch nicht genug: Bis zu sechs Sets mit drei Einheiten können parallel geschaltet werden, um eine riesige Ladekapazität zu erzielen PowerControl – Arbeiten mit begrenzter Generatorleistung, eingeschränktem Land- oder NetzstromDer MultiPlus ist ein sehr leistungsstarkes Batterie-Ladegerät. Daher nimmt er vom Generator bzw. der Landstromversorgung viel Strom auf. Mit dem Fernbedienungspanel Multi Control kann der maximal zu entnehmende Netz- bzw. Generatorstrom eingestellt werden. Der MultiPlus nimmt dann Rücksicht auf weitere angeschlossene Wechselstromverbraucher und nutzt zum Laden nur den Strom, der noch „übrig“ ist. So wird verhindert, dass der Generator- oder der Landstromanschluss überlastet wird. PowerAssist – “Leistungssteigerung“ von Generatoren und LandanschlussunterstützungMit dieser Funktion erhält das PowerControl-Prinzip eine neue Dimension. Sie ermöglicht, dass der MultiPlus zu schwach ausgelegte alternative Quellen stützt. Lastspitzen treten häufig nur für einen begrenzten Zeitraum auf. In einem solchen Fall stellt der MultiPlus sicher, dass eine zu schwache Landstrom- bzw. Generatorleistung sofort durch Energie aus der Batterie kompensiert wird. BackUp-System: Wechselstrom auch bei NetzausfallDer Multiplus kann sowohl bei nicht netzgekoppelten sowie bei netzgekoppelten PV-Anlagen als auch bei anderen alternativen Energiesystemen eingesetzt werden. Es ist eine Software zur Erkennung eines Netzausfalls verfügbar. Einfache SystemkonfigurationWenn Einstellungen an einem Einzelgerät verändert werden müssen, kann dies innerhalb von wenigen Minuten mithilfe eines DIP-Schalter-Einstellungsverfahrens erfolgen.Parallel geschaltete und Drei-Phasen-Systeme können mit der VE.Bus Quick Configure- und VE.Bus System Configurator Software konfiguriert werden. Überwachungsoptionen und Steuerung vor OrtEs stehen mehrere Optionen zur Verfügung: Batteriewächter, Multi Control Panel, Ve.Net Blue Power Panel, Color Control Panel, Smartphone oder Tablet (Bluetooth Smart), Laptop oder Computer (USB oder RS232). Überwachung und Steuerung aus der Ferne Victron Ethernet Remote, Victron Global Remote und das Color Control Panel ermöglichen Fernwartung und Fernüberwachung des MultiPlus. Zudem lassen sich die Systemdaten auf der VRM (Victron Remote Management) Website kostenlos speichern und einsehen

The inverterInverter RS Smart Solar Victron Energy is a combination of a powerful 48VDC, 6KVA 230VAC inverter and a high-voltage solar loader with 80-450 VDC, 4 kW Mppt. Thanks to its modern design and high-frequency technology, the inverter weighs only 10 kg and has an excellent efficiency, low standby performance and very quiet operation. The inverter creates a perfect sine wave that is able to supply devices with high performance. It is fed by a bidirectional DC-DC converter, which either charges the battery when excess solar energy is available or converted by the battery if it is needed.The inverter is equipped with a display to display battery, inverter and solar loading details. These parameters can also be read out by the VictronConnect app via Bluetooth. In addition, the inverter has a VE.Direct-and a Ve.CAN port for connection to a GX device for system monitoring. CharacteristicsNet-independent solar inverterCombination of inverter, bidirectional DC DC converter and MPPTLarge MPPT voltage range: 80-450VDC, PV start voltage 120VDCLight, efficient and quietVe.can and ve.direct connectionBuilt-in PV isolatorE/A connectionsLight, efficient and quiet Thanks to the high frequency technology and a new design, this powerful inverter weighs only 10 kg. In addition, it has an excellent efficiency, low standby performance and very quiet operation. Display and BluetoothThe display reads the battery, inverter and solar loader parameters. The same parameters can be accessed with a smartphone or another Bluetooth-enabled device. In addition, Bluetooth can be used to set up the system and change settings with VictronConnect. Technical specificationsInverter:Input voltage area: 38-64V DCOutput voltage: 230V AC ± 2%, frequency: 50 Hz ± 0.1%Output power: Linear rises from 4800W at 46VDC to 5300W at 52VDCTop performance: 9000W for 3 secondsCharger:Constant charging voltage: 57.6 VDCConservation charging voltage: 55.2 VDCMax. Charging current: 100aBattery temperature sensor: yesGeneral:Operating temperature range: -40 ° C - +65 ° CAir humidity: max. 95% (non -condensing)Protection class: IP21Weight: 11 kgDimensions: 425 x 440 x 125 mm

TheVictron Easysolar-II 48/3000/35-32 mppt 250/70 GX device combination Victron Energy combines an inverter/charger, a solar loader and a GX device. The elements are preloaded and integrated in a single unit. This simplifies most installations and saves time and money. Components- Multiplus II inverter/charger-SmartSolar Mppt 250/70-TR solar loader- GX device with 2x 16 characters displayDisplay and Wi-FiThe display shows parameters for battery, inverter and solar loader. The parameters can be accessed with a smartphone or another Wi-Fi-enabled device. Wi-Fi can also be used to set up the system and change settings. Solar loaderThe DC output of the SmartSolar Mppt is switched in parallel to the DC connection of the Multiplus II inverter/charger. The on/off mechanism of the Multiplus-II also controls the SmartSolar Mppt GX deviceThe integrated GX device includes:-A BMS-CAN interface. This can be used to connect to a compatible battery managed by the CAN bus. Note that this is not a Ve.can-compatible connection.- a USB connection- an Ethernet connection- a Ve.direct connectionThe GX device controls the Multiplus-II and the SmartSolar with a Ve.Bus and a Ve.Direct connection. Technical specificationsInverter: - Input voltage area 38-66V - Output voltage 230 VAC - Cons. Output power 3000W, top performance 5500WCharger: - Input voltage area 187-265 VAC - Entrance frequency 45-65Hz - Max. Batterieladestrom 35aSolar loader: - Max. Output current 70a - Max. PV performance 4000W - Max. PV empty voltage 250V - Constant charging voltage 57.6VInterfaces: BMS-CAN, USB, Ethernet, Ve.direct, Wi-FiProtection class: IP21Dimensions: 506 x 275 x 237 mmWeight: 26kg

TheVictron Easysolar-II 24/3000/70-32 mppt 250/70 GX Combines an inverter/charger, a solar loader and a GX device. The elements are preloaded and integrated in a single unit. This simplifies most installations and saves time and money. Components:Multiplus II inverter/chargerSmartSolar Mppt 250/70-TR solar loaderGX device with 2x 16 characters displayDisplay and Wi-FiThe display shows parameters for battery, inverter and solar loader. The parameters can be accessed with a smartphone or another Wi-Fi-enabled device. For setting up and changing system and settings. Solar loaderThe DC output of the SmartSolar Mppt is switched in parallel to the DC connection of the Multiplus II inverter/charger. The on/off mechanism of the Multiplus-II also controls the SmartSolar Mppt GX device- BMS-CAN interface. This can be used to connect to a compatible battery managed by the CAN bus. Note that this is not a Ve.can-compatible connection.-USB connection, Ethernet connection, VE.Direct connectionThe GX device controls the Multiplus-II and the SmartSolar with a Ve.Bus and a Ve.Direct connection. Technical specificationsInverter: - Input voltage area 38-66V- Output voltage 230 VAC- Cons. Output power 3000W- Top performance 5500WCharger: - Input voltage area 187-265 VAC- Entrance frequency 45-65Hz - Max. Batterieladestrom 70aSolar loader: - Max. Output current 70a - Max. PV performance 4000W - Max. PV empty voltage 250V - Constant charging voltage 57.6VInterfaces: BMS-CAN, USB, Ethernet, Ve.direct, Wi-FiProtection class: IP21Dimensions: 506 x 275 x 237 mmWeight: 26kg

TheMultiplus-II 48/10000/140-100 from Victron Energy is a high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 100 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 10000 W or 8000 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 140 A charging power and is supplemented by a 100 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features -PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- used as a backup device in network -coupled systems for the power supply for network failuresCan be used in various ESS (Energy Storage System) applications-for professional seafaring, yachts, vehicles and land -bound, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure software*technical features1000 W power with non -linear load 800 W continuous load and 18000 W peak outputfor 48 V battery voltage, 100 A transfer switch and 140 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. Effect is 95%, protection class IP22Always enough power thanks to PowerControl and Power AssistA maximum network or generator current can be set on the Multiplus-II 48/100-100. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. If the load is reduced, i.e. consumers are switched off, the energy that is sufficiently existing can then be used again for charging the batteries. Solar power: A changeover also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Many options for system expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

TheVictron Easysolar-II 48/5000/70-50 mppt 250/100 GX Victron Energy combines an inverter/charger, a solar loader and a GX device. The elements are preloaded and integrated in a single unit. This simplifies most installations and saves time and money. Components-Multiplus II inverter/charger-SmartSolar Mppt 250/100-TR solar loader control- GX device with 2x 16 characters displaySolar charging controller: Smartsolar Mppt 250/100-TR The integrated loading controller comes from the SmartSolar series of Victron and guarantees maximum yields with the ultra -fast MPPT procedure. Especially when the sky is covered, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield compared to PWM charging controls by up to 30 % and compared to slower MPPT regulators by up to 10 %.Critical partial shading of the solar modules Is recognized by the MPP controller and a new operating point is being sought so that even and the most unfavorable circumstances can still be achieved. The DC output of the SmartSolar Mppt is switched in parallel to the DC connection of the Multiplus II inverter/charger. The in/off mechanism of the Multiplus-II also controls the SmartSolar. Multiplus II 48/5000/70-50 inverter and battery charger The multiplus-II 48/5000/70-50 from Victron is a device combination of 4000 W Sinus inverter and Battery charger. The smart integrated battery charger makes impressive 70 A so that the batteries can be loaded extremely quickly if land/network current is available. The Sinus voltage converter integrated in the Multiplus transforms the 48 V DC from the battery into a 230 V AC voltage. Thanks to the real sine wave, the quality of the voltage is also perfect for sensitive electronic devices. GX deviceThe integrated GX device includes:-A BMS-CAN interface. This can be used to connect to a compatible battery managed by the CANBUS. Note that this is not a Ve.Cankomatibled connection. - a USB connection - an Ethernet connection - a Ve.direct connectionThe GX device controls the Multiplus-II and the SmartSolar with a Ve.Bus and a Ve.Direct connection. Advertisement and wifiThe display shows parameters for battery, inverter and solar loader. The parameters can be accessed with a smartphone or another Wi-Fi-enabled device. Wi-Fi can also be used to set up the system and change settings. The following properties are characterized by the high-end device:- 4000 W continuous output AC, 9000 W peak output - 48 V battery system voltage - inverter with pure sinus, suitable as a UPS - Max. 5800 W PV performance - Charge of the main battery with up to 70 a - Transfer switch with 50 a - Color Control display for settings and display of system information Technical specifications:Inverter: - Input voltage 38-66V - Output voltage 230 VAC - Kont. Output power 4000W - Top performance 1000W - Transfer switch 100a - Max. Effect 95% Charger: - Input voltage: 187-265 VAC - Entrance frequency 45-65 Hz - Constant charging voltage 57.6V - charging current 70a Solar loader: - Mppt 150/100-MC4 - Max. Output current 100A - Max. PV performance 5800W - Max. Effect 98% - Constant charging voltage 57.6V Operating temperature range: -40 ° C - +65 ° C Protection class: IP21 Dimensions: 604 x 323 x 253mm Weight: 39 kg

TheMultiplus 48/5000/70-100 from Victron Energy is a device combination of 48V 4000W sinus inverter and battery charger. The permanently integrated battery charger makes a considerable 70a which can also be fully charged even if the land/network current is available. The 48V Sinus voltage converter built into the multiplus converted its electricity from the battery into 230V AC. Thanks to the real sine wave, the electricity quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning -fast transfer switch is also installed with which numerous network -coupled solutions can also be implemented. In addition to the Ve.Bus Port, a COM port is also available for system integration, which almost enables unlimited networking of the Multiplus. comprehensive and flexible can be usedSince he also has a lightning -fast 100a transfer switch in addition to inverning people and charger, he is an ideal inverter for the areas of motorhome, boat or yacht and the network -coupled area of ​​the uninterrupted power supply in the case of network fluctuations or power failures. Also for use in network -coupled self -consumption systems that only draw electricity from the supplier if the battery current is no longer sufficient or as a UPS solution in which the multiplus stipulate when the electricity suddenly fails from the network operator and thus ensure an uninterrupted power supply. Essential performance features- 4000W continuous output and 10000W peak output, for 48V battery voltage-Device combination made of inverter with 100A transfer switch and 70a battery cador- delivers the purest 230V sine voltage and a clean 50Hz frequency- Ve.Bus communication sport ensures extensive possibilities of networking, system integration, configuration and control of the multiplus devices from Victron.-support the three-phase operation (3 equal units of the same model required)- In parallel, up to 6 devices can be connected in parallel and the system performance can therefore be significantly increased if necessary- 2 AC exits: For example, devices can be connected to the second output that should only run when network current is available- COM port in addition to the Ve.Bus port available, so that there are no longer any limits to the system integration- PowerControl function enables working with limited generator performance as well as limited land or network electricity- Power assist function enables “increase in performance” by generators and land connection support if necessary- Can be used as a UPS solution for interruption -free power supply, thanks to the integrated transfer switch with 100A switching capacity - For network -coupled self -consumption systems that can only be used by the network operator if the battery capacity is no longer sufficient or other programmable events have taken place- Compatible with numerous Victron tax and display panels- Three phase operation with identical multiplus interim judges possiblesolid performance expansion possibleApart from the parallel connection, three units of the same model can also be configured for a three-phase output. However, this is not enough: up to six sets with three units can be switched in parallel to achieve a huge 75 kW / 90 kva inverter and over 2,000 A charging capacity (calculated with the 5000 version) PowerControl - Working with limited generator performance, limited land or network electricity The Multiplus is a very powerful battery charger. Therefore, it takes up a lot of electricity from the generator or the land power supply (almost 10a per 5kva multi at 230 VAC). With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity for charging, which is still “left”. This prevents the generator or land power connection from being overloaded. Power assist - “increase in performance” by generators and country connection support With this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land current or generator output is immediately compensated for by energy from the battery. Backup system: Alternating current even in the event of a network failure The Multiplus can be used in both non-linked and network-coupled PV systems as well as in other alternative energy systems. Software is available for recognizing a network failure. Simple system configuration If settings have to be changed to a single device, this can be done within a few minutes using a DIP switch setting process.Parallel switched and three-phase systems can be configured with the Ve.Bus Quick Configuret- und Ve.Bus System Configurator software. Monitoring options and controls on site Several options are available: battery teacher, Multi Control Paneel, Ve.net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), Laptop or Computer (USB or RS232). Monitoring and control from a distance Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the Multiplus. In addition, the system data can be saved and viewed free of charge on the VRM (Victron Remote Management) website. Configuration from a distanceIf systems are connected to the Ethernet with a color control panel, you can be accessed and settings can be changed from a distance.

TheMultiplus 12/3000/120-16 from Victron Energy is a device combination of 12V 2400W sinus inverter and battery charger. The permanently integrated battery charger does a considerable 120a which can also be fully charged even if the land/network current is available. The 12V Sinus voltage converter built into the multiplus converts its electricity from the battery into 230V AC. Thanks to the real sine wave, the electricity quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning -fast transfer switch is also installed with which numerous network -coupled solutions can also be implemented. In addition to the Ve.Bus Port, a COM port is also available for system integration, which enables limitless networking of the Multiplus. comprehensive and flexible can be usedSince he also has a lightning -fast 16A transfer switch in addition to inverning people and charger, it is an ideal inverter for the areas of motorhome, boat or yacht and the network -coupled area of ​​the uninterrupted power supply in the case of network fluctuations or power failures. Also for use in network -coupled self -consumption systems that only draw electricity from the supplier if the battery current is no longer sufficient or as a UPS solution in which the multiplus stipulate when the electricity suddenly fails from the network operator and thus ensure an uninterrupted power supply. Essential performance features2400W continuous output and 6000W peak output, for 12V battery voltageDevice combination of inverter with transfer switch and 120a battery chargerdelivers the purest 230V sinus voltage and a clean 50Hz frequencyVe.Bus communication sport ensures extensive possibilities of networking, system integration, configuration and control of the multiplus devices from Victron.Support the three-phase operation (3 equal units of the same model required)Multiplus devices are parallel -switched, up to 6 devices can be connected in parallel and the system performance can therefore be significantly increased if necessary2 AC exits from Multiplus 3000 and larger. For example, devices that should only run can be connected to the second output if network current is availablefrom the Multiplus 3000 a COM port in addition to the VE.Bus port available, so that there are no longer any limits to the system integrationPowerControl function enables working with limited generator performance as well as limited land or network electricityPower assist function enables “increase in performance” by generators and land connection support in the event ofcan be used as a UPS solution for interruption -free power supply, thanks to the integrated transfer switch with 16A or 50Afor network -coupled self -consumption systems that can only be used by the network operator if the battery capacity is no longer sufficient or other programmable events have taken placeCompatible with numerous Victron tax and display panelsThree phase operation with identical multiplus interverters possiblesolid performance expansion possibleApart from the parallel connection, three units of the same model can also be configured for a three-phase output. However, this is not enough: up to six sets with three units can be switched in parallel to achieve a huge 75 kW / 90 kva inverter and over 2,000 A charging capacity (calculated with the 5000 version) PowerControl - Working with limited generator performance, limited land or network electricity The Multiplus is a very powerful battery charger. Therefore, it takes up a lot of electricity from the generator or the land power supply (almost 10a per 5kva multi at 230 VAC). With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity for charging, which is still “left”. This prevents the generator or land power connection from being overloaded. Power assist - “increase in performance” by generators and country connection support With this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land current or generator output is immediately compensated for by energy from the battery. Backup system: Alternating current even in the event of a network failure The Multiplus can be used in both non-linked and network-coupled PV systems as well as in other alternative energy systems. Software is available for recognizing a network failure. Simple system configuration If settings have to be changed to a single device, this can be done within a few minutes using a DIP switch setting process.Parallel switched and three-phase systems can be configured with the Ve.Bus Quick Configuret- und Ve.Bus System Configurator software. Monitoring options and controls on site Several options are available: battery teacher, Multi Control Paneel, Ve.net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), Laptop or Computer (USB or RS232). Monitoring and control from a distance Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the Multiplus. In addition, the system data can be saved and viewed free of charge on the VRM (Victron Remote Management) website. Configuration from a distanceIf systems are connected to the Ethernet with a color control panel, you can be accessed and settings can be changed from a distance.

TheMultiplus-II 48/15000/200-100 from Victron Energy is a new high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 100 A and the potential area of ​​application extends to eating applications. The inverter module provides a whopping 15000 W or 12000 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 200 A charging power and is supplemented by a 100 A transfer switch, with which it can be switched back and forth between the AC connections. Important performance features -PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- used as a backup device in network -coupled systems for the power supply for network failuresCan be used in various ESS (Energy Storage System) applications-for professional seafaring, yachts, vehicles and land -bound, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation- Can be configured on site or from a distance using Veconfigure software*technical features15000W power with non -linear load 1200 W continuous load and 27,000 W Top outputFor 48 V battery voltage, 100 A transfer switch and 200 A battery chargerOutput voltage: 230 VAC, frequency: 50 HzMax. Effect is 95%, protection class IP22Always enough power thanks to PowerControl and Power AssistA maximum network or generator current can be set on the Multiplus-II 48/15000/200-100. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. If the load is reduced, i.e. consumers are switched off, the energy that is sufficiently existing can then be used again for charging the batteries. Solar power: A changeover also in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters. Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Many options for system expansionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary). GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel. Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.

TheSun inverter Combines a Sinus inverter and a PWM solar charger in a housing and is easy to install with a minimum of cabling.With the inverter you can operate household appliances that need 230 VAC via leisure or car batteries with a voltage of 12 V.The solar charger ensures that the batteries are loaded by the energy obtained by their solar panels. The loading algorithm can be programmable.The parameters of the inverter and the solar loader can be read out with the VictronConnect app via Bluetooth. In addition, the inverter has a VE.Direct port to connect to a GX device or global link 520 for system monitoring.Model:12V | 250VA Proven reliabilityThe complete bruise with a ring transformer panel has also proven itself for years. The inverters are short -circuit -resistant and protected against overheating (whether caused by overload or by the ambient temperature).High switch -on powerThis is required to switch on consumers such as voltage formers for LED lamps, halogen lamps or power tools.Eco modeIn ECO mode, the inverter switches to standby mode when the load has a preceded value (minimum load: 15 W). In standby mode, the inverter then switches on for a short period of time (regulable default setting: every 2.5 seconds). If the load exceeds a preset limit, the inverter remains on.PWM solar chargerThe solar charger ensures that the batteries are loaded by the energy obtained by their solar panels. The loading algorithm can be programmable.Remote-controlled input/outputThe Phoenix inverter Control Ve.direct Remote Panel (not included) can be used for remote-controlled switching on and off the inverter. Alternatively, a remote-controlled on/off switch can be connected with a two-pin connector or between the plus pole of the battery and the left contact of the two-pin connector.LED diagnosisPlease note the description in the manual.BluetoothThe parameters of the inverter and the solar loader can be read out and monitored with the VictronConnect app via Bluetooth.Ve.direct communication connectionThe VE.Direct connection can be used for connection to a GX device, with global link 520 for monitoring via the VRM portal or with the VictronConnect app for monitoring or configuration with a computer.Monitoring via the VictronConnect app or a GX device:• Input and output voltage of the inverter and % load• Solar power, voltage and current strength• Operating condition and alarmsFully configurable via the VictronConnect app:• Alarm triggering with low battery voltage and reset level• Switching off with low battery voltage and restarting stages• Dynamic shutdown: load -dependent shutdown limit• Output voltage 210 - 245 V and frequency 50 or 60 Hz• Eco mode on/off and Eco mode Sense level• Batterieladestrom, algorithm and tensions• Temperature compensation for battery charging or shutdown of the level at low temperatureLoad switching on another change of alternating current: the automatic transfer switchWe recommend our Filax Automatic Transfer Switch for our low -performance inverter. With the Filax, switching takes place very quickly (in less than 20 milliseconds), so that an interruption -free operation of computers and other electronic devices is guaranteed.DC and PV connections with screw terminalsNo special cable connections or tools are required for installation.Available with an IEC-320 socketAn IEC-320 connector is included.

TheQuattro 12/5000/220-100/100 Victron Energy is a device combination of 12V 4000W Sinus inverter, a powerful battery loader and transfer switch. It has two switchable alternating stream outputs and 2 alternating current inputs, each equipped with a 100A transfer switch. The Quattro can be connected to two independent alternating current sources: for example to the public power grid and a generator or two generators. The Quattro automatically connects to the active source.The permanently integrated battery charger does a considerable 120a which can also be fully charged even if the land/network current is available. The 12V Sinus voltage converter built into the Quattro converts its battery current into 230V AC. Thanks to the real sine wave, the electricity quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning -fast 50a transfer switch per alternating current input is installed. Thanks to these switches, countless applications can also be implemented in the network -coupled area. In addition to the Ve.Bus Port, 2 Com ports are also available for system integration, which enables limitless networking of the quattro. 2 AC incoming and 2 alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the Quattro takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only delivers electricity if an alternating current is available on one of the inputs of the Quattro. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output. Essential performance features -4000W continuous output and 8000W peak output, for 12V battery voltage-Ccodere combination of inverters with a transfer switch and 220a battery cador-Utlegert 230V sinus voltage and a clean 50Hz frequency-2 alternating current inputs with integrated transfer switch / 2 x 100 A maximum power can be switched-2 AC exits +1 Additional output which only allows electricity to consumer if the alternating current input is active.-Ve.bus communication sport ensures extensive possibilities of networking, system integration, configuration and control of the multiplus devices from Victron.-Hear the three-phase operation (3 equal units of the same model required)-Multiplus devices are in parallel, up to 6 devices can be connected in parallel and the system performance is significantly increased if necessary-2x Com ports are available in addition to the Ve.Bus port, so that the system integration is actually no limits to the system integration-PowerControl function enables working with limited generator performance as well as limited land or network electricity-Powerassist function enables “performance increase” by generators and land connection support if necessary-As UPS solution for interruption -free power supply can be used, thanks to the integrated transfer switch with 16A or 50A-For network -coupled self -consumption systems, that can only be used by the network operator if the battery capacity is no longer sufficient or other programmable events have taken place-3 separate programmable relays-Compatible with numerous Victron tax and display panels-Iter high efficiency and low self -consumptionsolid performance expansion possibleUp to 6 quattros can be switched in parallel. This results, for example, with six 48/10000/140 units 54 kW/60 kva power or 840 A charging current. Three units can be switched in a three-phase configuration. However, this is not enough: up to 6 sets with three devices can be switched in parallel and you get 162 kW/180 KVA inverter performance and over 2,500 A loading capacity. PowerControl - Working with limited generator performance, limited land or network electricityThe Multiplus is a very powerful battery charger. Therefore, it takes up a lot of electricity from the generator or the land power supply (almost 10a per 5kva multi at 230 VAC). With the remote control panel Multi Control, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity for charging, which is still “left”. This prevents the generator or land power connection from being overloaded. Power assist - “increase in performance” by generators and country connection supportWith this function, the PowerControl principle receives a new dimension. It enables the quattro to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Quattro ensures that too weak land electricity or generator output is immediately compensated for by energy from the battery. Backup system: Alternating current even in the event of a network failureThe Quattro can be used for both non-mesh-coupled and pv systems coupled in the mesh-coupled PV systems as well as in other alternative energy systems. Software is available for recognizing a network failure. Simple system configurationIf settings have to be changed to a single device, this can be done within a few minutes using a DIP switch setting process.Parallel switched and three-phase systems can be configured with the Ve.Bus Quick Configuret- und Ve.Bus System Configurator software. Monitoring options and controls on siteSeveral options are available: battery teacher, Multi Control Paneel, Ve.net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth Smart), Laptop or Computer (USB or RS232). Monitoring and control from a distance Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the Multiplus. In addition, the system data can be saved and viewed free of charge on the VRM (Victron Remote Management) website. Configuration from a distanceIf systems are connected to the Ethernet with a color control panel, you can be accessed and settings can be changed from a distance.

TheMultiplus 24/22000/50-32 from Victron Energy is a device combination of 24V 2000W sinus inverter and battery charger. The permanently integrated battery charger makes a considerable 50a which can also be fully charged even, even spacious batteries can be fully loaded when the land/network current is available. The 24V Sinus voltage converter built into the multiplus converted its electricity from the battery into 230V AC. Thanks to the real sine wave, the electricity quality is also perfect for sensitive electronic devices. In addition to the two integrated device types, a lightning -fast 32A transfer switch is also installed with which numerous network -coupled solutions can also be implemented. For system integration, the Multiplus has a Ve.Bus port that enables limitless networking. Comprehensive and flexible can be usedSince he also has a 32A transfer switch in addition to inverts and charger, it is an ideal inverter for the areas of motorhome or yacht and the network -coupled area of ​​the uninterrupted power supply in the event of network fluctuations or power failures. Also for use in network -coupled self -consumption systems that only draw electricity from the supplier if the battery flow is no longer sufficient or as a UPS solution in which the multiplus stipulate, e.g. if the electricity is out of the network operator and then ensure an interruption -free power supply. Essential performance features-1600W continuous output and 3500W peak output, for 24V battery voltage-Ccodere combination of inverters with a transfer switch and 50a battery charger-Utlegert 230V sinus voltage and a clean 50Hz frequency-Ve.bus communication sport ensures extensive possibilities of networking, system integration, configuration and control of the multiplus devices from Victron-Hears the three-phase operation (3 equal units of the same model required)-Multiplus devices are in parallel, up to 6 devices can be connected in parallel and the system performance is significantly increased if necessary-PowerControl function enables working with limited generator performance as well as limited land or network electricity-Powerassist function enables “performance increase” by generators and land connection support if necessary-As UPS solution for interruption -free power supply can be used, thanks to the integrated transfer switchCan be used for network -coupled self -consumption systems that only draw electricity from the network operator if the battery capacity is no longer sufficient or other programmable events have taken place-Compatible with numerous Victron tax and display panelssolid performance expansion possibleApart from the parallel connection, three units of the same model can also be configured for a three-phase output. But that's not all: up to six sets with three units can be switched in parallel to achieve a huge charging capacity PowerControL- Working with limited generator performance, limited land or network electricityThe Multiplus is a very powerful battery charger. Therefore, it absorbs a lot of electricity from the generator or the land power supply. With the Multi Control remote control panel, the maximum network or generator current can be set. The Multiplus then takes into account other connected alternating current consumers and only uses the electricity for charging, which is still “left”. This prevents the generator or land power connection from being overloaded. Power assist - “increase in performance” by generators and country connection supportWith this function, the PowerControl principle receives a new dimension. It enables the multiplus to support too weak alternative sources. Load tips often only occur for a limited period of time. In such a case, the Multiplus ensures that too weak land current or generator output is immediately compensated for by energy from the battery. Backup system: Alternating current even in the event of a network failureThe Multiplus can be used in both non-linked and network-coupled PV systems as well as in other alternative energy systems. Software is available for recognizing a network failure. Simple system configurationIf settings have to be changed to a single device, this can be done within a few minutes using a DIP switch setting process.Parallel switched and three-phase systems can be configured with the Ve.Bus Quick Configuret- und Ve.Bus System Configurator software. Monitoring options and control on siteSeveral options are available: battery teacher, Multi Control Panel, Ve.net Blue Power Panel, Color Control Panel, smartphone or tablet (Bluetooth smart), laptop or computer (USB or RS232). Monitoring and control from a distance Victron Ethernet Remote, Victron Global Remote and the Color Control Panel enable remote maintenance and remote monitoring of the Multiplus. In addition, the system data can be saved and viewed free of charge on the VRM (Victron Remote Management) website. Configuration from a distanceIf systems are connected to the Ethernet with a color control panel, you can be accessed and settings can be changed from a distance.

TheQuattro-II 48/5000/70-50/50 from Victron Energy is a device