Clamps, Distributors, and Busbars
LYN020102000
Victron lynx power in
The Victron Lynx Power in-module (MPN LYN020102000) is used to connect batteries via an external backup. This can be useful if you have several parallel strings. Due to the extremely high short -circuit current potential of most batteries, it is recommended to use an external safety system with a suitable error vacuum assessment (e.g. an NH HRC).
Properties of the Victron Lynx Power in
1000a
Negative and positive DC collecting rail
easy installation
Part of the modular Lynx distribution system
Construction
The power in module contains a negative and a positive DC collection rail with M8 screws to connect the battery cables. Cables with a diameter of up to 22mm can be guided through the lower introductions and over the two side connections.
Scope of delivery:
1x victron lynx power in
LYN060102000
Victron Lynx distributor
The Victron Lynx Distributor (MPN Lyn060102000) is a modular DC collection rail with devices for four DC fuses. It monitors the status of each backup and shows its respective conditions via an LED on the front. The Lynx distributor contains a positive and a negative collective rail and offers a connection for 4 individual DC devices, loads or DC groups. It offers space for individual DC fuses per DC group.
Properties of the Victron Lynx distributor
Connection for four individual DC devices, loads or groups
Positive and negative collective track
Mega fuses
easy installation
Part of the modular Lynx distribution system
Security indicator LEDs
If you want to use the security indicator LEDs on the Lynx distributor, a connection to a Lynx Shunt is also required. The Lynx Shunt contains the required width of input current supply (8V-70V DC) in order to output the required 5V (4.5-5.5V) electricity requirements of the Lynx distributor conductor plate. The RJ11 cable required for connection is included. The Lynx Shunt has two ports, both of which can be used.
With full functionality, only the central LED shines green. If a fuse is burned (or missing), the LEDs of the central and security cycle shine red. If you do not use all connection points in your DC distribution, reactive fuses may need to be attached to delete the red LEDs.
Fuses
The Lynx distributor uses mega fuses. Please note that some mega fuses are only designed for 36V (suitable for 24V systems). For 48V systems, backups with a nominal voltage of 58/64V must be used.
Scope of delivery:
1x victron lynx distributor
data sheet
Weight
2.2 kg
Manufacturer
Victron Energy
Dimensions (LXBXH)
288 x 170 x 77.5 mm
Manufacturer part number
Lyn060102000
EAN
8719076022633
1x RJ11 cable
3203
VOTRONIC Plus distributor 6
Delivery time: 1-3 working days!
Plus distributor 6
The compact, powerful plus distributor with 6 individual circuits enables the professional distribution and protection of small and medium-sized consumers on the battery plus side. Two large collective terminals (cable cross-sections up to 16 mm², current carrying capacity max. 50 A) are used for the power supply from the battery, which can also be used for a further positive through distribution. The fuse holders on the consumer side are designed for commercially available FKS fuses with ratings of 1 A to 20 A; The scope of delivery includes the types 15 A, 10 A and 4 x 7.5 A. The associated six distribution terminals allow cable cross-sections of up to 4 mm² with a maximum current carrying capacity of 20 A. Labeling fields on the housing enable the fuses to be easily assigned to their circuits. Suitable for 12 V and 24 V operation.
Plus distributor 8
Powerful plus distributor with six fused outputs of different strengths.
The positive lead from the battery is connected to a solid screw block with a cable lug (cable cross-section 16 mm², total current capacity max. 96 A). The distribution takes place on:
Connection 1:
Screw block with cable lug (16 mm²) and strip fuse 40 A, 50 A or 60 A, with LED display, as main fuse or for larger loads such as inverters up to 12 V / 600 W or 24 V / 1200 W, powerful chargers, etc.
Connection 2:
6 mm² screw terminal with 30 A flat plug fuse, eg for medium consumers or chargers. This branch can be powered by an internal jumper from the main circuit or alternatively separately from the other circuits via a second 6 mm2 screw terminal.
Connection 3-6:
Screw terminals with a large clamping area (4 mm², max. 20 A) and fuse holder for standard FKS fuses with ratings of 1 A to 20 A; The scope of delivery includes the strengths 1 x 30 A and 2 x 15 A and 2 x 10 A.
The cover hood with cable routing comb ensures that the cables are held securely and that the appearance is clean. The monitoring LED for the strip fuse of connection 1 is also visible when the distributor housing is attached. Labeling fields on the housing enable the safe assignment of the plug-in fuses. Suitable for 12 V and 24 V operation.
device type
Art.-
No.
battery voltage
[V]
Dimensions (W x H x D)
[mm]
weight
[G]
Plus distributor 6 1
3203
12 and 24
90x38x60
95
A
Plus distributor 8 2
3215
12 and 24
105x36x71
135
B
Approval:
CE, E-test (EMC/Automotive Directive)
Scope of delivery 1 :
Blade fuses 1 x 15 A, 1 x 10 A and 4 x 7.5 A, operating instructions
Scope of delivery 2 :
2x cable lugs 16mm², strip fuse 40 A, 50 A, 60 A,
Blade fuses 1 x 30 A, 2 x 15 A and 2 x 10 A, operating instructions
Also available in boat version with moisture-proof electronics!
LYN060102010
Victron Lynx Distributor (M10)
Lynx Distributor (M10)from Victron Energy is a modular DC busbar that is part of your modular Lynx distribution system and has slots for up to four DC fuses.This rail continuously monitors the status of each individual fuse and signals this via illuminated LEDs on the front. It is supplied with power using the 40cm RJ10 cable supplied and can connect to a Lynx Smart BMS 500 or Lynx Smart BMS 1000.For further monitoring and communication, you can easily connect a Cerbo GX (also with display panel GX Touch 50 or GX Touch 70), CCGX or Venus GX . Up to 4 connected Lynx distributors can be monitored with one GX device.
Please note that the designation M10 refers to the connections of the busbars to which the modules are connected. In contrast, the connections for fuses and cables are always labeled M8.
The Lynx Distributor M10:- Supported system voltages: 12, 24 and 48 V - 1 mains LED - 4 LEDs for displaying the fuse status - Reverse polarity protection - Fuse detection - Housing material: ABS - App use possible - One positive and one negative busbar Positive busbar: 4 fused connections with fuse monitoring Negative busbar: 4 connections and one earth connection
Fuse detection:The distributor monitors each individual fuse and also detects them if they are blown. In the event of a blown fuse, the red fuse LED is activated, the operation LED turns red and an alarm message is sent to the connected Lynx Smart BMS at the same time. Fuse detection is possible for all fuses on the battery side as well as on the load or charging side. It is important to note that fuse detection has a special feature. If batteries are connected to multiple Lynx distribution circuits and a battery fuse blows, the fuse monitor will not alarm for the faulty fuse until a sufficiently high voltage is present on the fuse. This only happens after the battery has been charged or discharged.
Lynx distribution system:The system is a modular rail system that includes DC connectors, distributors, fuses, battery monitoring and/or lithium battery management functions. It consists of the following components:Lynx Power In - Plus and minus busbar with four connections for batteries or DC devices Lynx Distributor - Plus and minus busbar with four fused connections for batteries or DC devices and fuse monitoring Lynx Shunt VE.Can - positive busbar with free space for main fuse, negative busbar with shunt for battery monitoring, has VE.Can communication for setup with GX device Lynx Smart BMS - For use with Victron Energy Lithium Battery Smart batteries, Bluetooth communication via VictronConnect app or with a GX device, available as 500 A model with M8 busbars or 1000 A model with M10 busbars
VictronConnect app:The app is essential for setting up and monitoring! The following connection options are available: Bluetooth / USB, via the optional interface / remotely controlled via a GX device and the VRM portalThe app is available for the following platforms: Android / Apple IOS (USB is not supported, only a connection via Bluetooth is possible) / MacOs / Windows (Bluetooth is not supported, only a connection via USB is possible) The app can be downloaded from the respective app stores or from the Victron product page. Alternatively, a QR code is available. Technical data:
Voltage range: 9-60V DC
Nominal current: 1000A DC, uninterruptible
Max. Current consumption: 100 mA (when all LEDs are lit)
Power supply via Lynx Shunt VE.Can or Lynx Smart BMS 500 or Lynx Smart BMS 1000
Connection: 40 cm RJ10 cable
Protection class: IP22
Operating temperature range: -40°C - +60°C
Storage temperature range: -40°C - +60°C
Weight: 2.3 kg
Dimensions: 290 x 170 x 80 mm
Scope of delivery:1x Victron Lynx Distributor (M10)1x 40 cm RJ10 cable
BS2126
Blue Sea - collective rail 250a - 6 bolts Ø 7.9 mm
High -resistant collecting rail made of tinned copper, with 6 threaded bolt Ø 5/16 ”(7.9 mm). Usable for plus or minus pole. Voltage range max. 300 V AC /48 V DC, permanent load max. 250 a AC /DC. Dimensions (LXBXH): 197 x 38 x 43 mm.
You can find the right protective housing here.
3208
VOTRONIC minus distributor 12
Power distribution board
Proper electrical wiring in the vehicle is not just a question of orderliness, but rather an imperative to ensure safety on board. The frequently encountered tangle of cables, which continues from the battery behind the furniture walls, makes it more difficult to find the cause in the event of a fault and often poses a serious risk.
Small, indispensable helpers from the VOTRONIC peripheral equipment program can help here, and they take care of the professional distribution or protection of the positive side of the battery and ensuring safe mass ratios, among other things.
Minus distributor 12
Compact, powerful distributor on the battery negative side for 12 individual circuits. Two large collective terminals (cable cross-sections up to 16 mm², current carrying capacity max. 50 A) serve to feed current back to the battery; they can also be used for a further minus passage distribution.
On the consumer side, 12 distribution terminals allow the connection of cable cross-sections of up to 4 mm² with a maximum current carrying capacity of 20 A. The minus distributor 12 is particularly recommended for ground merging in isolating (plastic) vehicle bodies or in the case of insufficient ground ratios. The cover hood provides a clean look. Suitable for 12 V and 24 V operation.
Minus distributor 14
Efficient distributor on the battery negative side for 12 individual circuits. Particularly recommended for mass distribution with isolating (plastic) vehicle bodies or uncertain mass ratios. The negative lead is connected to a solid screw block with a cable lug (cable cross-section 16mm², total current carrying capacity max. 96 A). If required, another screw block is used for further minus passage distribution (cable lug 16 mm²). It is distributed to 4 terminals (6 mm², max. 32 A) and 8 terminals (4 mm², max. 20 A). These circuits are labeled 1-12. The cover hood with cable routing comb ensures that the cables are held securely and that the appearance is clean. Suitable for 12 V and 24 V operation.
Device type
Item-
No.
Battery voltage
[V]
Dimensions (W x H x D)
[mm]
weight
[g]
Minus distributor 12 1
3208
12 and 24
90x38x60
80
C
Minus distributor 14 2
3218
12 and 24
108x36x71
125
D
Check character:
CE, E-test (EMC/Automotive Directive)
Scope of delivery 1:
Instruction Manual
Scope of delivery 2:
2x cable lugs 16mm², operating instructions
Also available in boat version with moisture-proof electronics!
Delivery time: 1-3 working days
3215
VOTRONIC Plus distributor 8
circuit distributor
Proper wiring of electricity in the vehicle is not only a question of orderliness but rather an imperative to ensure safety on board. The frequently encountered tangle of cables, which continues from the battery behind the furniture walls, makes it difficult to find the cause in the event of a fault and often poses a serious risk.
This is where small, indispensable helpers from the VOTRONIC peripheral device program come in, which among other things take care of the professional distribution or protection of the battery plus side and secure ground conditions.
Plus distributor 6
The compact, powerful plus distributor with 6 individual circuits enables the professional distribution and protection of small and medium-sized consumers on the battery plus side. Two large collective terminals (cable cross-sections up to 16 mm², current carrying capacity max. 50 A) are used for the power supply from the battery, which can also be used for a further positive through distribution. The fuse holders on the consumer side are designed for commercially available FKS fuses with ratings of 1 A to 20 A; The scope of delivery includes the types 15 A, 10 A and 4 x 7.5 A. The associated six distribution terminals allow cable cross-sections of up to 4 mm² with a maximum current carrying capacity of 20 A. Labeling fields on the housing enable the fuses to be easily assigned to their circuits. Suitable for 12 V and 24 V operation.
Plus distributor 8
Powerful plus distributor with six fused outputs of different strengths.
The positive lead from the battery is connected to a solid screw block with a cable lug (cable cross-section 16 mm², total current capacity max. 96 A). The distribution takes place on:
Connection 1:
Screw block with cable lug (16 mm²) and strip fuse 40 A, 50 A or 60 A, with LED display, as main fuse or for larger loads such as inverters up to 12 V / 600 W or 24 V / 1200 W, powerful chargers, etc.
Connection 2:
6 mm² screw terminal with 30 A flat plug fuse, eg for medium consumers or chargers. This branch can be powered by an internal jumper from the main circuit or alternatively separately from the other circuits via a second 6 mm2 screw terminal.
Connection 3-6:
Screw terminals with a large clamping area (4 mm², max. 20 A) and fuse holder for standard FKS fuses with ratings of 1 A to 20 A; The scope of delivery includes the strengths 1 x 30 A and 2 x 15 A and 2 x 10 A.
The cover hood with cable routing comb ensures that the cables are held securely and that the appearance is clean. The monitoring LED for the strip fuse of connection 1 is also visible when the distributor housing is attached. Labeling fields on the housing enable the safe assignment of the plug-in fuses. Suitable for 12 V and 24 V operation.
device type
Art.-
No.
battery voltage
[V]
Dimensions (W x H x D)
[mm]
weight
[G]
Plus distributor 6 1
3203
12 and 24
90x38x60
95
A
Plus distributor 8 2
3215
12 and 24
105x36x71
135
B
Approval:
CE, E-test (EMC/Automotive Directive)
Scope of delivery 1 :
Blade fuses 1 x 15 A, 1 x 10 A and 4 x 7.5 A, operating instructions
Scope of delivery 2 :
2x cable lugs 16mm², strip fuse 40 A, 50 A, 60 A,
Blade fuses 1 x 30 A, 2 x 15 A and 2 x 10 A, operating instructions
Also available in boat version with moisture-proof electronics !
Delivery time: 1-3 working days
3218
VOTRONIC minus distributor 14
Power distribution board
Proper electrical wiring in the vehicle is not just a question of orderliness, but rather an imperative to ensure safety on board. The frequently encountered tangle of cables, which continues from the battery behind the furniture walls, makes it more difficult to find the cause in the event of a fault and often poses a serious risk.
Small, indispensable helpers from the VOTRONIC peripheral equipment program can help here, and they take care of the professional distribution or protection of the battery plus side and secure mass ratios, among other things.
Minus distributor 12
Compact, powerful distributor on the battery negative side for 12 individual circuits. Two large collective terminals (cable cross-sections up to 16 mm², current carrying capacity max. 50 A) serve to feed current back to the battery; they can also be used for a further minus passage distribution.
On the consumer side, 12 distribution terminals allow the connection of cable cross-sections of up to 4 mm² with a maximum current carrying capacity of 20 A. The minus distributor 12 is particularly recommended for ground merging in isolating (plastic) vehicle bodies or in the case of insufficient ground ratios. The cover hood provides a clean look. Suitable for 12 V and 24 V operation.
Minus distributor 14
Efficient distributor on the battery negative side for 12 individual circuits. Particularly recommended for mass distribution with isolating (plastic) vehicle bodies or uncertain mass ratios. The negative supply line is connected to a massive screw block with a cable lug (cable cross-section 16mm², total current carrying capacity max. 96 A). If required, another screw block is used for further minus passage distribution (cable lug 16 mm²). It is distributed to 4 terminals (6 mm², max. 32 A) and 8 terminals (4 mm², max. 20 A). These circuits are labeled 1-12. The cover hood with cable routing comb ensures that the cables are held securely and that the appearance is clean. Suitable for 12 V and 24 V operation.
Device type
Art.-No.
Battery voltage[V]
Dimensions (W x H x D)[mm]
Weight [g]
Minus distributor 12 1
3208
12 and 24
90x38x60
80
C
Minus distributor 14 2
3218
12 and 24
108x36x71
125
D
Check character:
CE, E-test (EMC/Automotive Directive)
Scope of delivery 1:
Instruction Manual
Scope of delivery 2:
2x cable lugs 16mm², operating instructions
Also available in boat version with moisture-proof electronics!?
Delivery time: 1-3 working days
020001050
Philippi STV 105 circuit distributor
Type Philippi STV 105
5 circuits with thermal circuit breakers 8 A, LED display, rocker switches and DC and USB double charging socket.
Dimensions : W 110 x H 145 x D 70 mm
Recommended terminal blocks type RKL 10.
Delivery time: 1-3 working days
8-01-013355-002
Dual Terminal Stud / 2-way Screw Connection with Removable Insulation Plate 2 x M10
2-fold connection bolts for connecting several lines to one sourceSuitable for use in 12V, 24V and 48V systemsUsable in motorhomes, on boats or in stationary systemsScope of delivery: 2 Set connection bolt red / blackMaterial composition: glass fiber reinforced nylon + tinned copperDimensions: 48.5 x 43 x 32 (38) mm --- Weight: 70g
600042000
Philippi row clamp, 20 -pin - RKL20
Delivery time: 4-5 working days
20 consumer clamps 4 mm², 2 connection terminals 25 mm² (+pole), 1 connection clamp 25 mm² (-pole). To connect between the switching board and consumers. The incoming consumer lines are clamped 2-pin. Two connections for cables from 25 mm² are available for the main electricity supply. The connection terminals for consumers are designed for up to 4 mm². The minus lines of consumers are all brought together here.Dimensions (LXBXH): 350 x 57 x 50 mm
020002040
Philippi STV 204 circuit distributor
The circuit distributors of the 200 series are equipped with thermal security machines from the E-T-A 3130 series.The 10A types are standard, 6a, 10a, 16a or 20a can be used on request. A sheet with lettering signs (SKZ) is included.
Version: 4 circuits with thermal rocker protection switches 10 A.
Dimensions: W 105 x H 105 x D 70 mm
020002100
Philippi STV 210 circuit distributors
The circuit distributors of the 200 series are equipped with thermal security machines from the E-T-A 3130 series. The 10A types are standard, 6a, 10a, 16a or 20a can be used on request. A sheet with lettering signs (SKZ) is included.
Version: 10 circuits with thermal rocker protection switches 10 A.
Dimensions: W 105 x H 210 x D 70 mm