The EasySolar-II GX device combination (MPN: PMP242307010) from Victron Energy combines a powerful MultiPlus-II inverter/charger, a SmartSolar MPPT 250/70-Tr solar charge controller, and a GX device with a 2x 16-character LCD display in a single enclosure. The components are pre-wired and combined in a single unit to save you time and simplify all related installation procedures.
Key features of the EasySolar-II GX
Automatic uninterruptible switching
Two AC outputs
Three-phase operation
PowerControl
Power Assist
Programmable relay
Remote control
LCD display
BMS-Can connections
Ethernet and WLAN
Operation in series with the grid
The EasySolar-II GX uses surplus PV energy to charge the batteries or feed it into the grid, and when necessary, it discharges the batteries or draws power from the grid to compensate for missing PV energy. In the event of a power failure, it disconnects from the grid and continues to supply the connected consumers. If certain loads need to be switched off when there is no AC input, this can be done via a second output. These loads are monitored by the PowerControl and PowerAssistant functions to limit the AC input to a safe level.
How it works Parallel to the grid
The EasySolar-II GX uses information from an optionally available external AC sensor or an electricity meter to maximize self-consumption and regulate the feed-in of electricity to the grid if necessary. In the event of a power failure, it continues to supply essential consumers. A current sensor with a capacity of 100A and a sensitivity of 50mA is used to implement these power functions and optimize self-consumption with external current measurement. The maximum current is either 50A or 100A and the connection cable has a minimum length of 1m. The following current transformers are available as optional extras:
Victron current transformer 100A:50mA for MultiPlus-II (1m) wire end
Victron current transformer 100A:50mA for MultiPlus-II (5m) wire end
Victron current transformer 100A:50mA for MultiPlus-II (20m) wire end
Three-phase operation
The device can be connected to other products and configured for a three-phase output. It is possible to connect up to 6 groups of three-phase units in parallel to provide an inverter power of 45kW/54kVA and a charging capacity of over 600A.
PowerControl – Optimizing the power supply with limited AC power
The EasySolar-II GX has the ability to handle an extremely high charging current. This places a considerable strain on the AC input. Therefore, the product allows the setting of a maximum current level. In this way, it takes into account the needs of other power-driven devices and uses only the remaining surplus power for the charging process.
PowerAssist – Extended use of generator or shore power
This extension adds an extra dimension to the PowerControl concept, enabling the product to supplement the performance of the alternative power source. In the event of peak power requirements, which are often only needed for a short time, the product ensures immediate compensation through battery power if the AC input power is insufficient. As soon as the load decreases, the excess power is used to charge the battery.
Display and WiFi
The display shows information about the battery, inverter, and solar charge controller parameters. This information can then be accessed and analyzed via a smartphone or other WiFi-enabled device. In addition, WiFi allows you to configure the system and adjust settings. Victron Energy's free website or app for remote monitoring (VRM) also allows you to view all your system information in a comprehensive graphical format. the portal can be used to make remote system adjustments and receive alarm notifications by email.
Technical data
General
Interfaces: BMS-Can, USB, Ethernet, VE:Direct, WiFi
Operating temperature range: -20°C to +45°C
Protection class: IP21
Weight: 26 kg
Dimensions: 499 x 268 x 237
Inverter
Input voltage range: 19-33 V
Nominal direct current: 150 A
Nominal battery voltage: 24 V
Output voltage: 230V AC
Frequency: 50 Hz
Continuous output power (at 25°C): 3000 VA / 2400 W
Continuous output power (at 40°C/55°C): 2200 W / 1700 W
Max. input power: 3000 VA / 2470 W
Rated current: 11 A
Peak power: 5500 W
Max. efficiency: 94%
Charger
Input voltage range: 187-265 V AC
Input frequency: 45-55 Hz
Charging voltage (constant voltage): 28.8 V
Charging voltage (trickle charge): 27.6 V
Storage mode: 26.4 V
Max. battery charging current: 70 A
SmartSolar chargecontroller
MPPT 250/70-Tr
Max. output current: 70 A
Max. PV power: 2000 W
Max. PV open-circuit voltage: 250 V
Max. PV short-circuit voltage: 35 A
Max. efficiency: 99%
Self-consumption: 20 mA
Constant charging voltage: 57.6 V
Float charging voltage: 55.2 V
Scope of delivery:
1x Victron Energy EasySolar-II GX 24/3000/70-32 MPPT 250/70 GX
1x user manual
