Brands
Tip
PMP482505010
Victron MultiPlus-II 48/5000/70-50
The Multiplus-II 48/5000/70-50 from Victron Energy is a high-end device combination that combines the classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 100 A and extends the potential range of use to ESS applications. The inverter module delivers a full 5000 W with a non-linear load and 4000 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 70 A charging power and is supplemented by a 50 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed.
Important features- PowerControl and PowerAssist - increase of mains or generator power- built-in anti-islanding function and connection option for external current sensor (optional)- can be used as a backup device in grid-connected systems;for power supply in the event of mains failures- can be used in various ESS (Energy Storage System) applications- ideally suited for professional shipping, yachts, vehicles and land-based, off-grid applications- VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration- virtually unlimited power through parallel and three-phase operation- can be configured locally or remotely using VEConfigure softwaretechnical features- 5000 W power with non-linear load 4000 W continuous load and 9000 W peak power- for 48 V battery voltage, 50 A transfer switch and 70 A battery charger- output voltage: 230 VAC, frequency: 50 Hz- max. efficiency is 95%, protection class IP22always enough power thanks to PowerControl and PowerAssistA maximum mains or generator current can be set on the Multiplus-II 48/5000/70-50. The MultiPlus-II then takes account of other connected AC consumers and only uses the current that is still "available" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to charge the batteries again.Solar power: Alternating current even in the event of a grid failureThe device can be used for both off-grid and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output.
Many options for system expansionThe settings can be changed within a few minutes using the VEConfigure software (requires a computer or laptop and an MK3 USB interface).Multiple monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, laptop, computer, Bluetooth (with the optional VE.Bus Smart Dongle), battery monitor, Digital Multi control panel.
Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.
3324
VOTRONIC 3324 VCC 1212-30 B2B charging converter charging booster
Votronic battery charging booster for motorhomes
12V / 30A
Optimized charging characteristics for acid, gel, AGM and LIFEPO4 batteries
High performance on short driving routes
Votronic Products "" Made in Germany ""
Charging booster, optimal load even on short lines
The Votronic Lade Booster guarantee the optimal and quick load of the supply battery from the alternator while driving. In contrast to the simple separation relay, the charging voltage is raised to the value, which is necessary for the respective battery type for a full load and required by the battery manufacturers. In this way, the full charging current can flow and in a short time invite handsome amounts of electricity into the battery. Long charging lines and losses, as well as voltage fluctuations on the alternator, are cleaned cleanly.
The Votronic loading technology has been used in professional emergency vehicles such as fire brigade, ambulance, coast guard for years! Quality - Made in Germany!
The loading converters thus also provide the well-known high-quality quality of the battery charge of the Votronic chargers while driving. The intelligent microprocessor charging with "iU1ou2" charging characteristics and dynamic charging time calculation automatically ensures the fast and gentle full load as well as subsequent loading of the connected batteries from any state of charge and always enables simultaneous co-supply of consumers to the supply battery.
Further special features at a glance:
Votronic Products "" Made in Germany ""
High charging capacity already on short routes
Significantly improved energy balance of the on -board battery
Optimal charging characteristics for all battery types adjustable by battery selection switches (lead-acid, gel, AGM, lithium lifepo4)
Suitable for all alternators
Automatic, adjustable performance control ensures the priority loading of the starter battery by the alternator when the vehicle is heavily loaded and thus ensures the immediate starting capacity of the vehicle again
Easy installation, no interventions in the vehicle of the vehicle required, device is switched into the charging line to the supply battery
Parallel operation for the increase in performance possible
Especially recommended for vehicles with Euro 6 standard
Temperature sensor 825 already included
The loading converters are also characterized by compact design, low weight (high -frequency switching transmission, switch fashion technology) and vigorously dimensioned power components. 6 Operating advertisements provide information about the operating status of the device at any time.
As accessories we recommend the clear LCD Charge Control S-VCC (1248). With this you always have information about loading, the display was developed exclusively for the VCC 1212 device series.
Scope of delivery:- Votronic 3324 VCC 1212-30 12V to 12V 30A B2B charging converter- temperature sensor- Operation manual
Technical specifications
VCC-1212-30
Input voltage (DC)
12V (10.5 - 16.5V)
Charging performance adjustable limit, max.
30a
Battery type
Gel, AGM, lead acid, lifepo4
Steplessly temperature -controlled fan
Yes
Temperature sensor included
Yes
Connections remote control, display / VBS2 / CI bus
Yes / no / no
Overload protection / over -temperature protection
Yes / Yes
Battery capacity, recommended/up to
60-200/260 Ah
Dimensions
146 x 67 x 40mm
Weight
0.28 kg
"
PMP482305010
Victron MultiPlus-II 48/3000/35-32
The Multiplus-II 48/3000/35-32 is a high-end device combination from Victron Energy that combines classic Multiplus components with an external current sensor and integrated anti-islanding function. This extends the PowerControl and PowerAssist functions to 50 A and extends the potential range of use to ESS applications. The inverter module delivers a full 3000 W with a non-linear load and 2400 W with a linear continuous load. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, which can be used to switch back and forth between the AC connections at lightning speed.
Important features- PowerControl and PowerAssist increase mains or generator power- Built-in anti-islanding function and connection option for external current sensor (optional)- Can be used as a backup device in grid-connected systems;t in grid-connected systems for the power supply in the event of grid failures- can be used in various ESS (Energy Storage System) applications- ideally suited for professional seafaring, yachts, vehicles and land-based, off-grid applications- VE.Bus interface for parallel and three-phase operation, remote monitoring and system integration- virtually unlimited power through parallel and three-phase operation- can be configured on site or remotely using VEConfigure software- technical features- 3000W power with non-linear load 2400 W continuous load and 6000 W peak power- for 48 V battery voltage, 2400 W continuous load and 6000 W peak power- for 48 V battery voltage, 2400 W continuous load and 6000 W peak power;for 48 V battery voltage, 32 A transfer switch and 35 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- max. efficiency is 95%, protection class IP22- always enough power thanks to PowerControl and PowerAssist
A maximum mains or generator current can be set on the MultiPlus-II 48/3000/35-32. The MultiPlus-II then takes account of other connected AC consumers and only uses the current that is still "available" to charge the battery. This prevents the generator or mains connection from being overloaded (PowerControl function). The PowerAssist function adds a new dimension to the PowerControl principle. Load peaks often only occur for a limited period of time. In such cases, the MultiPlus-II immediately compensates for insufficient generator, shore power or mains power with energy from the battery. If the load is reduced, i.e. consumers are switched off, the available energy can then be used to charge the batteries again.Solar power: alternating current even in the event of a grid failureThe device can be used for both non-grid-connected and grid-connected PV systems as well as other alternative energy systems. It can be used with both solar charge controllers and grid-connected inverters.Maximum flexibility thanks to two AC outputsThe main output ensures uninterrupted operation. In the event of a mains failure or an interruption in the shore/generator power supply, the MultiPlus-II takes over the supply to the connected loads. The switchover takes place so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic devices is guaranteed. The second output only supplies power if alternating current is available at the input of the MultiPlus-II. Consumers that must not discharge the battery, such as a water heater, can be connected to this output. Many options for system expansionThe settings can be changed within minutes using the VEConfigure software (a computer or laptop and an MK3 USB interface are required) and several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, CANvu GX, Laptop, Computer, Bluetooth (with the optional VE.Bus Smart Dongle), Battery-Wächter, Digital Multi Control Panel.
Remote configuration and monitoringInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be stored and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, they can be accessed remotely and settings can be changed.
ASS030140000
Victron MK3-USB VE.Bus to USB Interface
Das MK3 USB zu VE.Bus Interface von Victron Energy verbindet Ihren Computer oder ein Notebook mit einer Vielzahl von Victron Produkten über den VE.Bus Port.
Das Interface versetzt Sie in die Lage, eine ganze Reihe von Victron Programmen zu nutzen um Ihr Victron Produkt zu konfigurieren und zu analysieren. Der einfachste Weg komplexe Systeme oder Einzelgeräte auf Ihre Bedürfnisse einzustellen.
folgende kostenlose Programme können mit Hilfe des Interfaces genutzt werden:
VEConfigure 3 (v9004193)
VE.Bus Quick Configure (v9010137) – Für die Installation von 3 phasigen System, zum Beispiel mit drei Multiplus Wechselrichtern.
VE.Bus System Configurator (v9009132) – Für komplexe Systeme
VEFlash (v9005147) – für einfache Firmware-Updates von Victron Produkten mit VE.Bus.
folgende Geräte-Familien sind aktuell mit dem VE.Bus zu USB Interface kompatibel:
Multi
MultiGrid
MultiPlus
Quattro
Phoenix Wechselrichter (Nur Modelle mit einem VE.Bus-Kommunikationsanschluss)
ECOmulti
EasySolar
EasyPlus
Lieferumfang:
1x Victron Energy ASS030140000 MK3-USB (VE.Bus to USB) Interface
LYN020102000
Victron lynx power in
The Victron Lynx Power in-module (MPN LYN020102000) is used to connect batteries via an external backup. This can be useful if you have several parallel strings. Due to the extremely high short -circuit current potential of most batteries, it is recommended to use an external safety system with a suitable error vacuum assessment (e.g. an NH HRC).
Properties of the Victron Lynx Power in
1000a
Negative and positive DC collecting rail
easy installation
Part of the modular Lynx distribution system
Construction
The power in module contains a negative and a positive DC collection rail with M8 screws to connect the battery cables. Cables with a diameter of up to 22mm can be guided through the lower introductions and over the two side connections.
Scope of delivery:
1x victron lynx power in
LYN060102000
Victron Lynx distributor
The Victron Lynx Distributor (MPN Lyn060102000) is a modular DC collection rail with devices for four DC fuses. It monitors the status of each backup and shows its respective conditions via an LED on the front. The Lynx distributor contains a positive and a negative collective rail and offers a connection for 4 individual DC devices, loads or DC groups. It offers space for individual DC fuses per DC group.
Properties of the Victron Lynx distributor
Connection for four individual DC devices, loads or groups
Positive and negative collective track
Mega fuses
easy installation
Part of the modular Lynx distribution system
Security indicator LEDs
If you want to use the security indicator LEDs on the Lynx distributor, a connection to a Lynx Shunt is also required. The Lynx Shunt contains the required width of input current supply (8V-70V DC) in order to output the required 5V (4.5-5.5V) electricity requirements of the Lynx distributor conductor plate. The RJ11 cable required for connection is included. The Lynx Shunt has two ports, both of which can be used.
With full functionality, only the central LED shines green. If a fuse is burned (or missing), the LEDs of the central and security cycle shine red. If you do not use all connection points in your DC distribution, reactive fuses may need to be attached to delete the red LEDs.
Fuses
The Lynx distributor uses mega fuses. Please note that some mega fuses are only designed for 36V (suitable for 24V systems). For 48V systems, backups with a nominal voltage of 58/64V must be used.
Scope of delivery:
1x victron lynx distributor
data sheet
Weight
2.2 kg
Manufacturer
Victron Energy
Dimensions (LXBXH)
288 x 170 x 77.5 mm
Manufacturer part number
Lyn060102000
EAN
8719076022633
1x RJ11 cable
BPC123047002
Victron Blue Smart IP22 12/30 (1) Charger 12V 30A 1 battery
The Blue Smart IP22 12/30 (1) charger from Victron Energy (MPN BPC123047002) is a professional, compact 12V 30A battery charger of the latest generation with a charging output and built -in Bluetooth! The Blue Smart IP22 12/30 (1) charger can be used with devices in your workshop or with motor vehicles such as (classic) cars, motorcycles, boats and motorhomes and loads both classic 12V lead batteries and modern lithium batteries.
Highlights of the 12/30 (1) Blue Smart IP22 Charger
Intelligent charging until the perfect battery state ...
The seven-level loading algorithm gets the best out of her battery. The charger provides the battery the energy it needs, it keeps it in a healthy condition, ensures better performance ... and a longer life.
Restoration of deep-downloaded "dead" batteries
Unlike most other brands and product series, the Blue Smart IP22 charger will try to recharge a deep-discharged battery by forceing it out with a weak charging current. The normal charging operation is then resumed as soon as there is sufficient voltage between the battery connections.
Call the battery status from afar, with the VictronConnect app
The Blue Smart IP22 12/30 (1) charger has built -in Bluetooth. In this way, the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app.
The most important technical features of the 12/30 (1) Blue Smart IP22 Charger
Victron part number: BPC123042002
Lades 12V lead-acid, gel, agm and lithium batteries
30a maximum charging current
1 battery charging output
Very compact dimensions: 235 x 108 x 65mm
Highly modern, seven-level loading algorithm
With integrated Bluetooth for use with the free VictronConnect app
Other performance features of the 12/30 (1) Blue Smart IP22 battery loader
Trend -setting efficiency
With an efficiency of up to 94%, these chargers generate up to four times less heat compared to the industrial standard. After the battery has also been fully charged, electricity consumption drops to less than 0.5 watts, which is about five to ten times better than the industrial standard.
Adaptive 7-stable loading algorithm
The 12/30 (1) Blue Smart charger is characterized by its microprocessor-controlled, "adaptive" battery management. “Adaptive” means that the loading process is automatically adjusted to the type of battery use.
Storage mode: Less maintenance and aging in the resting state of the battery
The storage mode is always activated if no discharge has been carried out within 24 hours. The loading tension is then reduced to 2.2V/cell (13.2V for a 12V battery) in order to minimize the gas development and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gas voltage. This achieves a kind of compensation charge that prevents the electrolystal layering and sulfating - the two main reasons for premature battery failure.
Scope of delivery:
1x Victron Energy BPC123042002 12/30 (1) IP22 Blue Smart Charger
1x operating instructions
data sheet
Generally
item number
1-67-010615
EAN
8719076037453
Manufacturer part number
BPC123047002
Manufacturer
Victron
Dimensions (LXBXH)
10.8 x 23.5 x 6.5 cm
Weight
0.9 kg
VBS127010010
Victron Battery Switch on/Off 275a Battery main switch
The battery switch is intended for permanent current and is suitable for battery systems up to 48 V. It has a unique ergonomic and aesthetic button for easy operation.
use
With the battery switch, a battery of DC loads and/or DC load sources can be separated. It serves to maintain the battery charge for unattended systems, for system maintenance or in emergencies. With the battery switch, the house battery can also be switched in parallel to the starter battery to supplement a unloaded starter battery or a discharged house battery in an emergency.
installation
The battery switch offers both a surface and back wall assembly and is therefore flexible when installing. It has 4 easily removable side parts for cable access. It is supplied with 16 different label stickers for the individual design of the battery switch.
Security
The button is removable for insulation or security purposes. The battery switch corresponds to the ISO8846 Zuf protection standard and is suitable for use in a machine room.
Max. Permanent current 275 a
1-minute introduction 455 a
Nominal value Home 1250 a
Nominal voltage 48 V
Material of the clamps tinned copper
Material of the hexagon nut Tinned copper
Diameter of the clamp 3/8 inches / 9.53 mm
Recommended torque 70 LBF · Inch / 8 N · M
Base material glass fiber reinforced nylon
Weight 0.4 LB / 0.2 kg
Dimensions (L x W x H) 2.7 x 3.0 x 2.7 inches 69.5 x 76.3 x 69.5 mm
Assembly surface or back wall assembly
ISO8846 / SAE J1171
ASS030530218
Victron 1.8m Ve.direct cable connection cable
The 1.80m VE.Direct Cable from Victron (ASS030530218) is required to combine devices that are supposed to communicate via the VE-Direct Port. For example, the Bluesolar controller and the MPPT Control remote control panel.
The following connections can be established:
Victron Bluesolar Mppt controller to Victron Color Control GX Panel
Victron Bluesolar Mppt controller to Mppt Control remote control unit unit BMV70XXX series for Color Control GX Panel
BMV60XXX series for Color Control GX Panel
Phoenix inverter 12V 24V 48V 250W-500W to Color Control GX Panel
The VE.Direct cables are not included in the scope of delivery of these device series and are available in lengths of 0.3 to 10m.
Scope of delivery:
1x Victron Ass030530218 1.8m Ve.direct Cable
ASS030530209
Victron 0.9m Ve.direct cable connection cable
The 0.9m Ve.direct Cable from Victron (ASS030530209) is required to combine devices that are supposed to communicate via the VE-Direct Port. For example, the Bluesolar controller and the MPPT Control remote control panel.
The following connections can be established:
Victron Bluesolar Mppt controller to Victron Color Control GX Panel
Victron Bluesolar Mppt controller to Mppt Control remote control unit unit BMV70XXX series for Color Control GX Panel
BMV60XXX series for Color Control GX Panel
Phoenix inverter 12V 24V 48V 250W-500W to Color Control GX Panel
The VE.Direct cables are not included in the scope of delivery of these device series and are available in lengths of 0.3 to 10m.
Scope of delivery:
1x Victron Ass030530209 0.9m Ve.direct Cable
SCC115045212
Victron SmartSolar MPPT 150/45
The Smartsolar MPPT 150/45 from Victron Energy, belongs to the latest generation of smart solar controllers and processes 45A solar current and can work flexibly with 12/24/36/48 V batteries. Ultra-fast power tracking and automatic power point detection in the event of partial shading are just two of the many highlights of this new device class. The SmartSolar 150/45 is also available as a version with MC4 connections on the solar side of the charge controller instead of screw terminals. In addition, this model is capable of parallel operation with other controllers of the same type.In comparison to the BlueSolar series, the Bluetooth module is already permanently integrated into the controller in the Smartsolar family, making the smart dongle superfluous in this device. The optional MPPT WireBox-L Tr from Victron Energy is the ideal addition to your SmartSolar charge controller. It securely covers the cable entries and connection terminals of the controller, protecting them from external influences and contact.
Key product features The latest generation of ultra-fast MPP tracker ensures the best possible yield even in cloudy conditionsNominal charging current 45A, 150V maximum PV open-circuit voltageMaximum PV power: 12 V 650 W / 24 V 1300 W / 48 V 2600 WVictron Energy part number (MPN): SCC115045212automatic detection of the MPP voltage in partial shading ensures a further improvement in yield compared to "simple" MPPT charge controllersfixed integrated Bluetooth module for app-supported analysis and configuration of the controller (via free Victron app on compatible devices)integrated VE.Direct data communication port for communication with additional devices such as the GX Color Control Panel or a Smart BMV battery monitorHigh maximum efficiency of 98%Parallel operation with other 150/45 controllers possible;adjustable constant charge voltageadjustable float charge voltagesuitable for all AGM, GEL, lead-acid calcium-calcium and lithium batteriesfully programmable charging algorithms that can later be manually activated and switched via a switch on the housing;useintegrated protection against battery polarity reversalmulti-stage and adaptive charging algorithmremote switching on and off possible via 2-pin plugprotection class IP 43 for the electronic components and protection class IP 22 for the connection area of the controller;for the connection area of the controllerIntegrated temperature sensor balances maintenance and constant charging voltage according to temperatureDay/night time control and light dimming option130x186x701.3 kGSmart data communication via VE.Direct and BluetoothModern Apple and Android smartphones, tablets, Macbooks and other devices can be connected thanks to the permanently integrated Bluetooth module and the free Victron Connect APP. The app can then be used to configure many important functions of the MPPT 150/45 SmartSolar controller. Of course, it also provides all important parameters such as the current solar yield in real time. Maximum Power PointIn the event of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP. However, this may not be the optimum MPP. The innovative algorithm of the SmartSolar 150/45 will always maximize the energy yield by adjusting to the optimal MPP.
High-speed MPP trackerIn particular in overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.
Electronic protectionProtection against reverse polarity battery connectionPV reverse current blockingProtection against overheating of the deviceProtection against short circuitsProtection against reverse polarity PV connectionVE.Direct data communication portVE.Direct in text mode transmits all important parameters to other devices connected to the charge controller every second and thus offers the option of communicating with additional GX Color Control system panels. The VE.Direct connection is intended for products where full Canbus integration (VE-Direct) would be too expensive. Scope of delivery1x Victron SCC115045212 SmartSolar MPPT 150/45 12V 24V 36V 48V 45A charge controllerOperating instructions
Tip
PMP482306000
Victron Multiplus-II 48/3000/35-32 GX
TheMultiplus-II 48/3000/35-32 GX from Victron Energy Is a high-end device combination that combines classic multiplus components with an external current sensor and integrated anti-Icelanding function. As a result, the functions PowerControl and Power Assist are expanded to 50 A and the potential area of application extends to eating applications. The inverter module provides a whopping 3000 W or 2400 W with a linear permanent burden on non -linear loads. The 48 V battery charger is also very well proportioned with 35 A charging power and is supplemented by a 32 A transfer switch, with which it can be switched back and forth between the AC connections. Compared to the remaining devices of the series, the GX variants have an integrated GX display with numerous other connection options.
Important performance features- Integrated GX control device with various communication connections-PowerControl and power assist-increase in network or generator performance-Built-in anti-Icelanding function and connection option for external electricity sensor (optional)- can be used as a backup device in network -coupled systems for the power supply for network failures- Can be used in various ESS (Energy Storage System) Applications- Ideally suited for professional seafaring, yachts, vehicles and land -related, removable applications-Ve.Bus interface for parallel and three-phase operation, remote monitoring and system integration-Practically unlimited performance through parallel and three-phase operation.- Can be configured on site or from a distance using Veconfigure software*technical features- 3000W power with non -linear load 2400 W continuous load and 6000 W Top output- for 48 V battery voltage, 32 A transfer switch and 35 A battery charger- Output voltage: 230 VAC, frequency: 50 Hz- Max. Efficiency is 95%, protection class IP22- Always enough power thanks to PowerControl and Power Assist
A maximum network or generator current can be set on the Multiplus-II 48/3000/35-32 GX. The Multiplus-II then takes into account other connected alternating current consumers and only uses the electricity to load the battery, which is still “left”. This prevents the generator or mains connection from being overloaded (PowerControl function). With the power assist function, the PowerControl principle receives a new dimension. Load tips often only occur for a limited period of time. In such a case, the multiplus-II compensates for the weak generator, land electricity or network output immediately by energy from the battery. If the load is reduced, i.e. consumers are switched off, the energy that is sufficiently existing can then be used again for charging the batteries.
Solar power: Alternating current even in the event of a network failureThe device can be used for non-mesh-coupled and network-coupled PV systems as well as in other alternative energy systems. It can be used with solar charging regulators and with network-bound inverters.
Maximum flexibility thanks to two alternating current outputsThe main exit ensures uninterrupted operation. In the event of a network failure or in the event of an interruption of the land/generator current, the multiplus-II takes over the supply of the connected consumers. Switching happens so quickly (in less than 20 milliseconds) that an interruption -free operation of computers and other electronic devices is guaranteed. The second output only provides electricity if the Multiplus II AC. Consumers who are not allowed to unload the battery, such as B. a water heater can be connected to this output.
Scope of the integrated GX deviceA VE.CAN interface can be used to connect Victron (e.g. Ve.CAN MPPT) Ve.CAN devices. The connection can also be configured via the remote console for use with a compatible CAN bus Li-ion battery.1xusb connection, 1x Ethernet connection, 1x VE.Direct connection offer many options for system extensionThe settings can be changed with the Veconfigure software within a few minutes (a computer or laptop and an MK3 USB interface are necessary).Several monitoring and control options are available: Color Control GX, Venus GX, Octo GX, Canvu GX, Laptop, Computer, Bluetooth (with the optional Ve.Bus Smart Dongle), battery guard, digital multi operating panel .
Configuration and monitoring remotelyInstall a Color Control GX or other GX products to connect to the Internet. The operating data can be saved and viewed free of charge on our VRM (Victron Remote Management) website. If systems are connected to the Internet, you can access them from a distance and settings can be changed.
SHU050150050
Victron SmartShunt 500A/50mV battery monitor with Bluetooth
Smart battery monitoring
Victron Energy's SmartShunt 500A (MPN SHU050150050) is an all-in-one battery monitor. It connects via Bluetooth to the VictronConnect app on your phone (or tablet) and you can conveniently read out all monitored battery parameters, such as state of charge, remaining time, history information and much more. Settings can also be changed easily.
Alternatively, the SmartShunt can be connected and read by a GX device. Connection to the SmartShunt is via a VE.Direct cable.
The SmartShunt is a good alternative for a BMV battery monitor, especially for systems where battery monitoring is required but less wiring and clutter is desired.
Characteristics
Equipped with Bluetooth
Check battery parameters conveniently on your smartphone or tablet
Can be connected to GX device
Additional input for additional monitoring options
uncomplicated installation
Differences to the BMV-712 battery monitor
No programmable visual and audible alarm
No programmable relay
Why is battery monitoring important?
Batteries are used in many areas, in most cases to store energy for later use. However, the battery itself does not display the amount of energy stored.
Battery life depends on many factors. The service life can be shortened by undercharging or overcharging, deep discharging, excessive charging or discharging currents and high ambient temperatures. By monitoring with a battery monitor, the user receives important feedback so that countermeasures can be taken to extend the battery life if necessary.
Scope of delivery:
1x SmartShunt
2x cables with fuse, for '+' connection and starter battery or midpoint connection
You will find the right connection cable for the negative pole at Frenchman Energy here and an automotive cone here at Frenchman Marine here and the KFZ cone here
data sheet
IP protection
IP21
weight
0.4kg
Manufacturer
VictronEnergy
Dimensions (LxWxH)
75x135x85mm
Manufacturer part number
SHU050150050
EAN
8719076044253
ASS030572050
Victron 5m RS485 for USB Interface Cable
The 5m USB to RS485 Interface Cable from Victron Energy (MPN AS030571050) for combining energy meters ET112 or ET340 to the system control monitor Color Control GX or the system monitoring Venus GX.
Length: 5m
Occupation of the cables
RS485 Converter / Strom counter ET112 and ET340
Yellow (data) / Terminal 5
Orange (data+) / Terminal 4
Black (GND) /Terminal 6
The red, green and brown wire that comes from the USB to the RS485 cable is not used.
Scope of delivery:
1x Victron Energy Ass030571050 5M USB to RS485 Interface
data sheet
Weight
0.195 kg
Manufacturer
Victron Energy
guarantee
5 years of manufacturer's guarantee
Product
Assembly accessories
3326
Votronic 3326 VCC 1212-50 charging converter/B2B 50 AMP chargingbooster
The VCC 1212-50 from Votronic (3326) is a fully automatic, unisolved, battery charging converter for special vehicles, high-quality motorhomes, boat. The loading converter (booster) of the "VCC" series has been developed according to the latest specifications for the mobile load of supply batteries (living space/on-board batteries), from the alternator (starter battery) during the journey. The device also ensures During the journey for a complete iU1ou2 loading character. The max. Charging current of the VCC 1212-50 is 50a and it can work with lead-acid, gel, AGM1, AGM2 and LIFEPO4 batteries. This device loads from a 12V Battery / alternator a 12V battery.
In contrast to the conventional separating relay, the charging voltage is lowered or raised according to charging program specification, therefore 6, 6 + plus vehicles are particularly suitable for euro standard.
Universally usable multi -talent
For on-board batteries in classic lyricic acid, lead-gel or lead-agm and modern lithium-lifepo4 technology, the 8 selectable charging programs ensure a surveillance-free, quick and gentle full load from every charging state with subsequent full maintenance and maintenance of the battery. Even on short trips, the battery is loaded with full charging current. Connected 12 V consumers are automatically supplied, even if the on-board network is heavily loaded. The automatic performance control ensures the necessary safety and starting capacity of the vehicle.
Important features of the Votronic 3326 VCC 1212-50
The VCC 1212-50 is a B2B charger without galvanic insulation for charging 12V batteries from a 12V alternator / battery.
Max. Charging current: 50a, input voltage range 12V, loads 12V batteries, recommended battery capacity: 75 - 440AH
Increases or reduces the voltage to the necessary level in order to be able to precisely charge the on-board battery with the optimal charging characteristic.
It compensates for line losses and voltage fluctuations in the alternator, such as that, for example, fully occur in Euro 6 vehicles (intelligent alternators) to a considerable extent.
Is characterized by compact design, low weight (high-frequency switch fashion technology) and vigorously dimensioned performance components for safe operation.
Significantly better energy balance of the on-board battery. No intervention in the starter circle; The device behaves like a strong consumer on the alternator.
The 12 V consumers provided are protected against overvoltage and voltage fluctuations.
The charging voltage is free of tips and regulated so that an overload of the batteries is excluded.
Fully automatic operation: The device is constantly connected to the batteries and is automatically activated by the running alternator of the vehicle. When the engine is standing, the batteries are not unloaded.
Parallel and buffer operation: With simultaneous consumption, the battery is charged or fully received. The adjustment of the loading times calculates and monitors the device automatically.
Surveillance-free charge: multiple protection against overload, overheating, overvoltage, short circuit, misconduct and battery recharge through electronic discounting up to the complete separation of the device and battery.
Construction network filter installed: Problemless parallel operation with other load sources (EBL, chargers, engine and fuel generators, solar systems) on a battery.
Charging cable compensation: Tension losses on the charging cables are automatically excavated.
Connection for battery temperature sensor (sensor included).
In the case of lead batteries (acid, gel, AGM), the charging voltage is automatically adjusted to the battery temperature. This causes a better full load of the weaker battery in the cold, and unnecessary battery launch is avoided in summer temperatures.
LIFEPO4 batteries: battery protection at high and particularly adapted load at low temperatures below 0 ° C. Charging aid for low-level lead batteries: gentle invitation of the (lead-acid,-gel, AGM) battery up to 8 V, then powerful support of the battery with any still switched on consumers.
Also ensures the automatic activation of a Lifepo4 battery switched off by the BMS.
What added value does the use of a B2B loading converter offer me?
The loading converters ensure the optimal and quick load of the supply battery from the alternator while driving. In contrast to the simple separation relay, the charging voltage is raised to the value, which is necessary for the respective battery type for a full load and required by the battery manufacturers. In this way, the full charging current can flow and in a short time invite handsome amounts of electricity into the battery. Long charging lines and losses, as well as voltage fluctuations on the alternator, are cleaned cleanly. For loading converters with different input and output voltages (12V/24V or 24V/12V), the simple load of a second battery is possible even without installing a second alternator.
The loading converters thus also provide the well-known high-quality quality of the battery charge of the Votronic chargers while driving. The intelligent microprocessor charging with "iu1ou2ou3" charging characteristics and dynamic charging time calculation automatically ensures the fast and gentle full load as well as subsequent charging of the connected batteries from any state of charge and always enables simultaneous care for consumers in parallel to the care battery.
Scope of delivery:
1x Votronic 3326 VCC 1212-50 50A loading converter
1x operating instructions (German)
1x temperature sensor
Also available in boots with the electronics of protected electronics!
Technical specifications
Entrance of the vehicle starter battery "+ in Start"
Vehicle starter battery nominal voltage
12 V
Battery capacity (size), at least recommended
60 Ah
Input voltage area (Euro 6 +), D + controlled
10.5 - 16.5 V
Input overvoltage shutdown (Euro 6 +), max.
16.5 V
Performance recording max.
760 W
Electricity intake (with the lowest input voltage) max.
0.1 a - 68 a
Electricity recording limited, 3 switch positions "in limit"
49 a, 42 a, 33 a
Side load branch, charge/cargo maintenance for 12 V starter battery
With external mains charging, switch position "B"
0 - 3 a
Activation tax input "D+", from D+, Klemme 15, ignition
8 - 16.5 V
In "Start"-tension sensor lines "VS" and "VS+"
Yes / Yes
Switch output "TR", signal for bypass relay /max.
12 V / 1 a
Charging output on on-board supply battery "+ Out Bord"
Loading/buffer/load current, regulated iu1ou2, lead, lifepo
0 a - 50 a
Reduction in the case of switch position "out limit"
0 a - 39 a
Bley acid, -Gel, -GM battery nominal voltage
12 V
Capacity (battery size), recommended / up to
75-320/440 Ah
lead charging programs stored in the memory
4
Vorbadestrom (Battery deepest discharge <8V), max.
25 a
Safety charging voltage at battery over temperature
12.80 V
Lifepo4 battery nominal voltage
12 V (12.8 -13.3 V)
Capacity (battery size), recommended / up to
75-320/440 Ah
Lifepo4 charging programs stored in the memory
4
Safety charging voltage at battery over temperature
12.80 V
"T t" input for battery temperature sensor "Bord"
Yes
Out "Bord"-tension sensor lines "VB-" and "VB+"
Yes / Yes
Purchase current, standby
16 mA
Charging timer
3-way
Tension
<30 MV RMS
Charging stress limit "+out board" (protection of consumers)
15.00 V
External overvoltage shutdown "+out board" (20 sec)
15.50 V
Short circuit/back load/safety protection
Yes
Device installation position
any
Temperature range
-20 to 45 °
Speed -controlled, temperature -controlled fan
Yes
Gradual delegation of the charging capacity at over temperature
Yes
Safety shutdown at overheating
Yes
Dimensions, including fortified. Flanges and clamps (LXBXH)
135 x 160 x 72 mm
Weight
950 g
Ambient conditions, humidity: max. 95 % room moisture, not condensing
Scope of delivery: temperature sensor, operating instructions
ASS030530010
Victron Ve.direct to USB Interface Cable
The Victron Ve.direct to USB Interface (MPN AS030530010) is needed to pair VICTRON devices with VE.Direct connection via USB with the notebook or computer.
In this way you can conveniently evaluate performance data on the computer and configure the devices using a free software.
Which Victron devices are equipped with a VE.Direct connection?
• Bluesolar Mppt controller
• BMV battery monitors 700 + 702 Black
• Victron Phoenix Ve.direct voltage converter
• Color Control GX System Monitor
• Lithium Peak Power Packs
Scope of delivery:
1x Victron Ass030530010 VE.Direct to USB Interface
1x short guide
data sheet
Generally
Manufacturer
Victron Energy
EAN
8719076019589
SCC110020160R
Victron SmartSolar MPPT 100/20 (up to 48V)
The Smartsolar 100/20 up to 48V from Victron Energy is an MPPT solar charge controller with 20A max. charging current for charging 12V, 24V and 48V batteries. In contrast to the Bluesolar version, the Smart version has integrated Bluetooth, which makes the purchase of a Bluetooth dongel superfluous. In addition, a VE.Direct connection is still available for communication with other Victron devices such as the Color Control GX or the MPPT Control. The integrated Bluetooth in the SmartSolar series is the wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices. The optional MPPT WireBox-S 100-20 from Victron Energy is the ideal addition to your SmartSolar charge controller. It securely covers the cable entries and connection terminals of the controller, protecting them from external influences and contact.
Technical features:20A max. charging current. charging current, suitable for 12V and 24V batteriesnominal PV power for 12V systems: 290Wnominal PV power for 24V systems: 580Wnominal PV power for 48V systems: 1160W20A load outputhigh peak efficiency of 98%free programmable battery charging algorithm (üvia the free Victron Connect APP)Light dimming functions programmable (üvia the free Victron Connect APP)Ultrafast maximum power point trackingmax. PV open-circuit voltage: 100VCharging algorithm: multi-stage, adaptiveIntegrated Bluetooth module100x113x500.7kgUltrafast maximum power point trackingIn particular in overcast conditions, when the light intensity is constantly changing, an extremely fast MPPT controller improves the energy yield by up to 30% compared to PWM charging controllers and by up to 10% compared to slower MPPT controllers.
Intelligent load output Deep discharging of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a specified voltage value. Alternatively, an algorithm for intelligent battery management can be selected: see BatteryLife.The load output is short-circuit-proof.
Battery Life: intelligent battery managementIf the solar charge controller is not able to charge the battery to its full capacity within one day, the status of the battery constantly switches back and forth between "partially charged" and "end of discharge". This operating mode (no regular full charge) will damage a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the state of charge of the battery and, if necessary, raises the threshold for disconnecting the load day by day (i.e. the load is disconnected early), the load is disconnected earlier) until the energy gained is sufficient to charge the battery to almost 100%. From this point, the threshold for disconnecting the load is modulated so that charging to almost 100% is achieved approximately once a week. Scope of delivery:1x Victron Energy Smartsolar MPPT 100/20-48 20A 12V 24V 48V solar charge controller1x operating instructions
ORI121236140
Victron Orion-Tr Smart 12/12-30A Non-isolated DC-DC Wandler
The Orion Tr-Smart DC-DC from Victron Energy is a professional, DC to DC adaptive 3-stage charger with integrated Bluetooth, known on the market as a battery-to-battery (B2B) charger. The charge booster is suitable for use in dual battery systems in vehicles or on boats where the alternator and the starter battery are used to charge the service battery. The charger can be used in 12V or 24V systems and is suitable for both lead-acid and lithium batteries. Models up to 400W are available and an unlimited number of devices can be connected in parallel to increase the output power.
Properties:- Suitable for Bluetooth Smart- Fully programmable- Adaptive 3-stage charging algorithm- Remote on/off switching- Short-circuit proof- Parallel connection to increase the output current possible- Ambient temperature protection- Protection class IP43
Bluetooth Smart:Monitoring, changing settings and updating the charger with newly available software functions can be done with any Bluetooth-enabled smartphone, tablet or other device.
Adaptive 3-stage charging algorithm: Constant current - Constant voltage - Conservation- With lead batteries, it is important that the charging time is kept short during shallow discharges in order to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery is fully charged.- For lithium batteries, the recording time is fixed, with a default setting of 2 hours.- Alternatively, a fixed output voltage can be selected.
Remote on/off:A remote-controlled on/off switch or a relay contact can be connected to the two-pole plug. Alternatively, connection H (right) of the two-pin plug can be connected to a positive battery terminal or connection L (left) of the two-pin plug can be connected to the negative battery terminal (or to the body of a vehicle, for example).
Technical data:- Input voltage range: 10-17 V- Nominal output voltage: 12.2 V- Output voltage setting range: 10-15 V- Output voltage tolerance: ±0.2 V- Cont. Output current at rated output voltage and 40°: 30 A- Cont. Output power at 40°C: 360 W- Operating temperature range: -20°C - +55°C- Weight: 1.8 kg- Dimensions: 130 x 186 x 70 mm
Scope of delivery:1x Victron Energy Orion-Tr Smart DC/DC charge booster 12/12-30A (360W) ORI121236140
ORI121217040
Victron Smart Orion XS 12/12-50 A DC-DC battery charger
The Victron Energy Smart BuckBoost is a compact and efficient DC-DC converter with an output of 50A. This converter can perform both step-up and step-down conversion.
Thanks to its compact design, which corresponds to that of the SmartSolar 75/15, as well as an impressive efficiency of 98% (resulting in minimal heat generation) and a VE.Direct interface for monitoring and DVCC (Dynamic Voltage and Current Control), this device is ideal for optimizing the charging of LiFePO4 batteries by alternators, for example, or for charging lead battery circuits from a lithium battery bank.
The Victron Energy Smart BuckBoost can be used both as a battery charger and as a power supply unit with a wide input and output voltage range.
Battery charger mode:In charging mode, the four-stage charging algorithm extends the battery's service life through precise charging. Thanks to fully adjustable charging algorithms with eight pre-programmed battery setups, optimum charging is ensured for every type of battery. This is particularly important for vehicles with Euro 5 or 6 Smart alternators, which often deliver too low a charging voltage under unfavorable conditions.
The regulated charge also protects the alternator in lithium systems from overloading, as the low impedance of lithium batteries can lead to a high alternator current.
Power supply mode:In power supply mode, the output voltage remains stable regardless of load changes or fluctuations in the input voltage (within the specified range). The output voltage is fully adjustable and remains constant even if the input voltage fluctuates, thanks to the automatic buck-boost control. This regulation also ensures that the current never exceeds the set value, even if the input voltage is higher than the output voltage.
Intelligent motor detection:The Smart BuckBoost can be configured so that it only supplies current when the motor is running. This function is made possible by the integrated motor shutdown detection. This eliminates the need to adjust the vehicle wiring or add an additional engine detection sensor. This function also prevents the vehicle's on-board voltage from becoming too low. In addition to automatic detection, the Smart BuckBoost can also be activated via the remote on/off connection.
Configuration and monitoring:The Smart BuckBoost is programmed and monitored entirely via the VictronConnect app. This also enables remote access via VictronConnect-Remote (VC-R) when connected to a GX device that is connected to the VRM portal. Via the integrated VE.Direct port, the device can be monitored via the GX Remote Console or from a PC, Apple computer with macOS or Android device in conjunction with a VE.Direct to USB interface and VictronConnect.
Üvia a GX device, the Smart BuckBoost can also be intelligently controlled via DVCC, for example by a Lynx Smart BMS.
Waterproof and device-proof:The Smart BuckBoost complies with the IP65 standard, which means that the device is dustproof and can withstand heavy rain. The heat is dissipated by natural convection, which means there is no need for a loud fan.Specifications:- Input voltage range: 9-17 Volt- Output voltage adjustment range: 10-17 Volt- Output voltage tolerance: +/- 0.25 % (max)- Output voltage noise: 10 mV eff- Adjustment range for input and output current: 1-50 Ampere- Maximum constant short-circuit current: 50 Ampere- Continuous power up to 40 °C: 700 Watt- Maximum efficiency: 98.5 %- No-load current consumption: < 100 mA- Standby current consumption: < 1.5 mA- Operating temperature range: -20 to +60 °C (reduction of 1.5 % per °C üabove 40 °C)- Humidity: Max. 95 % non-condensing- DC connection: screw terminals- Maximum cable cross-section: 25 mm² (AWG4)- Weight: 0.330 kg (0.73 pounds)- Dimensions (H x W x D): 137.3 x 123.1 x 40 mm (5.4 x 4.85 x 1.6 inches)- Protection class: IP65
ASS030710018
Victron Ve.CAN to CAN-BUS BMS Type A cable 1.8m
You need this Ve.CAN to CAN BUS-BMS cable from Victron (MPN AS030710018) to connect a Victron GX device to a CAN bus-compatible battery that is not from Victron. The cable, with a length of 1.8m, corresponds to type A, which can be used for the following batteries:
BYD B-Box
Pylontech US2000C / US3000C / Force-L
installation
The page called "CAN-BUS BMS" is inserted into the battery. The other side with the name "Ve.can" must either be connected to the Ve.CAN port of the GX device or to the BMS-CAN port become. Both types of a GX device can be configured for use with a third-party CAN bus battery connected to a BMS. Information about the configuration can be found in the manual for the battery you use.
Scope of delivery:
1x Victron Ve.CAN to CAN-BUS BMS Type A Cable 1.8m (ASS030710018)
data sheet
Manufacturer
Victron Energy
Dimensions (LXBXH)
30 x 180 x 170 mm
Manufacturer part number
Ass030710018
EAN
8719076043317
BPC121531064R
Victron Blue Smart IP65 12/15 12V 230V battery charger Battery charger
The Blue Smart IP65 12/15 12V 230V battery charger is the latest professional charger from Victron Energy with built-in Bluetooth. It is designed for charging 12V batteries of various types and delivers a maximum charging current of 15A. Together with the free VictronConnect app, you can easily and smartly evaluate the activity of your battery charger via your smartphone, tablet or computer and even configure it to a certain extent.Technical highlights of the Blue Smart IP65 12/15 battery charger
Easy configuration and setup of the Blue Smart IP65 12/15 via Bluetooth interface
Suitable for all 12V battery types
max. 15A charging current
solid protection against splash water. Dust and chemicals thanks to protection class IP65
Provides several functions to extend the battery service life
automatic temperature adjustment at low and high temperatures
automatic power supply function
7-stage, intelligent charging algorithm
can restore fully discharged "dead batteries"
Provides low-energy mode for charging small batteries
Victron article number: BPC121531064R
Lithium-ion battery mode
Ultra-high efficiency "green" battery chargerWith an efficiency of up to 95%, these chargers generate three to four times less heat than the industry standard. And, once the battery is fully charged, power consumption is reduced to 0.5 watts, which is five to ten times better than the industry standard.Durable, safe and quiet
low thermal load on the electronic components
protected against the ingress of dust, water and chemicals
Protection against overheating: The output current is reduced linearly when the temperature rises to 60 °C, so the charger does not fail even at extreme temperatures
The chargers are absolutely noiseless thanks to passive cooling: no fan or other moving parts
ReconditioningA lead-acid battery that has not been sufficiently charged or has been left in a discharged state for days or weeks will deteriorate in performance due to sulphation. If the process is stopped in time, the sulphation can be partially reversed by charging the battery at a low current until a higher voltage is reached.Function for restoring fully discharged batteriesMost chargers with reverse polarity protection do not recognize a battery that has been discharged to zero volts or almost zero volts and therefore do not recharge it. However, the Blue Power charger attempts to recharge a fully discharged battery with low current and resumes the normal charging process after sufficient voltage has been built up via the battery terminals.Optional accessories for Blue Smart IP 65 12/15 BPC121531064R
12 V cigarette lighter plug with fuse
2 meter extension cable
Connection terminals with fuses
M6 cable lug connector with fuse
Scope of delivery:
1x Victron BPC121531064R Blue Smart IP65 12/15 12V 230V battery charger1x operating instructions1x connection terminals1x M8 cable lug connector
BPP900450110
Victron Cerbo GX MK2 system monitoring
The Cerbo GX MK2 offers small upgrades while retaining the form factor:
- All 3 USB ports are now fully functional- Two fully-fledged VE.CAN ports, allowing e.g. parallel VE.CAN and NM.e.g. parallel VE.CAN and NMEA2000 possible- VE.CAN 1 is now isolated- RJ45 connectors rotated by 180° for easier access to remove cables
Digital inputs can now be used as pulse counters
ASS030572018
Victron 1.8m RS485 for USB Interface Cable
The 1.8m USB to RS485 Interface Cable from Victron Energy (MPN AS030571018) for the connection of energy meters ET112 or ET340 to the system control monitor Color Control GX or the system monitoring Venus GX.
Length: 1.8m
Occupation of the cables
RS485 Converter / Strom counter ET112 and ET340
Yellow (data) / Terminal 5
Orange (data+) / Terminal 4
Black (GND) /Terminal 6
The red, green and brown wire that comes from the USB to the RS485 cable is not used.
Scope of delivery:
1x Victron Energy Ass030571018 1.8m USB to RS485 Interface
data sheet
Ambient temperature
-30c - +60c
Weight
0.08 kg
Manufacturer
Victron Energy
guarantee
5 years of manufacturer's guarantee
Product
Assembly accessories